Main Content

Bluetooth BR RF-PHY Transmitter Tests for Modulation Characteristics, Carrier Frequency Offset, and Drift

This example shows how to perform Bluetooth® basic rate (BR) radio frequency (RF) physical layer (PHY) transmitter tests specific to modulation characteristics, carrier frequency offset, and drift using the Communications Toolbox™ Library for the Bluetooth Protocol. The test measurements compute frequency deviation, carrier frequency offset, and drift values. This example also verifies whether these test measurement values are within the limits specified by the Bluetooth RF-PHY Test Specifications [1].

Objectives of Bluetooth RF-PHY Tests

The Bluetooth RF-PHY Test Specifications [1] defined by the Bluetooth Special Interest Group (SIG) include RF-PHY tests for transmitters and receivers. The objectives of these RF-PHY tests are to:

  • Ensure interoperability between all Bluetooth devices.

  • Ensure a basic level of system performance for all Bluetooth products.

Each test case has a specified test procedure. The expected outcome must be met by the implementation under test (IUT).

RF-PHY Transmitter Tests

The main goal of the transmitter test measurements is to ensure that the transmitter characteristics are within the limits specified by the Bluetooth RF-PHY Test Specifications [1]. This example includes transmitter tests relevant to modulation characteristics, carrier frequency offset, and drift. This table shows various RF-PHY transmitter tests performed in this example.

RF-PHY Transmitter Test Procedure

This block diagram summarizes the test procedure for transmitter tests relevant to modulation characteristics, carrier frequency offset, and drift.

Generate DH/DM packets and pass through the bluetoothWaveformGenerator function to generate Bluetooth test waveforms. This table shows the test waveforms and packet type(s) required for different test IDs:

Check for Support Package Installation

Check if the 'Communications Toolbox Library for the Bluetooth Protocol' support package is installed.

commSupportPackageCheck('BLUETOOTH');

Configure Simulation Parameters

You can change the txTestID, packetType, initFreqOffset, maxFreqDrift and sps parameters based on the transmitter test, packet type, initial frequency offset, maximum frequency drift, and samples per symbol, respectively.

txTestID = 'RF/TRM/CA/BV-07-C';
packetType = 'DH1';             % Select packet type as per transmitter test case ID
initFreqOffset =0; % Initial frequency offset in Hz
maxFreqDrift =0;   % Maximum frequency drift in Hz, [-25e3, 25e3] for one slot packet
                                               % [-40e3, 40e3] for three and five slot packets
sps = 32;                                      % Minimum of 4 samples per symbol as per test specifications

Generate Test Parameters

Test parameters are generated based on transmitter test, packet type, initial frequency offset, maximum frequency drift and samples per symbol. To generate payload, packet duration, and waveform configuration parameters, use helperBRModulationTestPacketConfig.m function. To design channel filter based on the sample rate, use helperModulationTestFilterDesign.m function. To add frequency offset and thermal noise, create and configurecomm.PhaseFrequencyOffset and comm.ThermalNoise System objects, respectively.

[payload,packetDuration,cfg] = helperBRModulationTestPacketConfig(txTestID,packetType,sps);
filtDesign = helperModulationTestFilterDesign('BR',sps); % Design channel filter
driftRate = maxFreqDrift/(packetDuration*sps);           % Drift rate
freqDrift = driftRate*(0:1:(packetDuration*sps-1))';     % Frequency drift for the packet
freqOffset = freqDrift + initFreqOffset;                 % Frequency offset, includes initial frequency offset and drift

% Create a phase frequency offset System object
sampleRate = sps*1e6;                                    % Sample rate in Hz
pfo = comm.PhaseFrequencyOffset('FrequencyOffset',freqOffset,'SampleRate',sampleRate);

% Create a thermal noise System object
NF = 12;                                                 % Noise figure (dB)
thNoise = comm.ThermalNoise('NoiseMethod','Noise figure', ...
                            'SampleRate',sampleRate, ...
                            'NoiseFigure',NF);

Simulate Transmitter Tests

To simulate the transmitter tests, follow these steps:

  1. Generate a Bluetooth BR waveform for the selected packet type and waveform configuration.

  2. Add frequency offset, which includes initial frequency offset and drift to the waveform.

  3. Add noise to the waveform.

  4. Perform filtering on the noisy waveform.

  5. Perform FM demodulation on the filtered waveform.

  6. Perform test measurements and display the pass verdict.

filtWaveform = zeros(packetDuration*sps,size(payload,2)); % Initialization
for i = 1:size(payload,2)
    txWaveform = bluetoothWaveformGenerator(payload(:,i),cfg);
    txWaveformValid = txWaveform(1:packetDuration*sps);
    wfmFreqOffset = pfo(txWaveformValid);
    wfmChannel = thNoise(wfmFreqOffset);
    filtWaveform(:,i) = conv(wfmChannel,filtDesign.Coefficients.','same');
end

Based on the transmitter test, the helperBRModulationTestMeasurements.m function performs FM demodulation and returns these values:

  • RF/TRM/CA/BV-07-C: Returns the frequency deviations and center frequencies for the two test sequences, freq1, freq2, respectively and maximum frequency deviation for the second test sequence, freq3.

  • RF/TRM/CA/BV-08-C: Returns the initial frequency offset, freq1.

  • RF/TRM/CA/BV-09-C: Returns the initial frequency offset and frequency drift, freq1 and freq2, respectively.

[waveform,freq1,freq2,freq3] = helperBRModulationTestMeasurements(filtWaveform,txTestID,sps,packetType);

The helperBRModulationTestVerdict.m function verifies whether the test measurements are within the specified limits and displays the verdict.

helperBRModulationTestVerdict(waveform,txTestID,sps,freq1,freq2,freq3)

Test sequence: 11110000
    Measured average frequency deviation: 160 KHz
    Expected average frequency deviation range: [140 kHz, 175 kHz]
    Result: Pass
Test sequence: 10101010
    Expected 99.9% of all maximum frequency deviation greater than 115 kHz
    Result: Pass
Ratio of frequency deviations in the two test sequences: 1.1462
Expected Ratio greater than 0.8
    Result: Pass

This example demonstrates the Bluetooth BR transmitter test measurements specific to modulation characteristics, carrier frequency offset, and drift. The simulation results verify that these computed test measurement values are within the limits specified by Bluetooth RF-PHY Test Specifications [1].

Appendix

The example uses these helpers:

Selected Bibliography

  1. Bluetooth Special Interest Group (SIG). “Bluetooth RF-PHY Test Specification”, v1.2/2.0/2.0, EDR/2.1/2.1, EDR/3.0/3.0, HS (), RF.TS/3.0.H.1, Section 4.5. 2009. https://www.bluetooth.com.

  2. Bluetooth Special Interest Group (SIG). "Core System Package [BR/EDR Controller Volume]". Bluetooth Core Specification. Version 5.2, Volume 2. https://www.bluetooth.com.