Modeling

Tutorials

Get Started

• Getting Started with Embedded Coder Support Package for Texas Instruments C2000 Processors
  This example shows you how to use Embedded Coder® Support Package for Texas Instruments™ C2000™ Processors to run a Simulink models on Texas Instruments C2000 hardware.
• Getting Started with Embedded Coder Support Package for F28M3x Concerto Processors
  In this example, you will learn how to configure a simple Simulink model to generate code for ARM and C28x cores of Concerto F28M3x processors and run the generated code on the board to periodically turn LEDs on and off.
• ADC-PWM Synchronization Using ADC Interrupt
  This example shows how to use the ADC block to sample an analog voltage and use the PWM block to generate a pulse waveform.
• LIN-Based Control of PWM Duty Cycle
  This example shows how to use the C28035 LIN Receive, LIN Transmit, and PWM blocks to generate a pulse waveform.
• Asynchronous Scheduling
  This example shows how to use the Texas Instruments™ c28x peripherals and Hardware Interrupt blocks to control the real-time execution of Simulink® function-call subsystems in an asynchronous fashion.
• Using the Control Law Accelerator (CLA)
  This example shows how to use the Control Law Accelerator (CLA) available on some of the TI® processors.
• Using the I2C Bus to Access Sensors
  This example shows how to use the I2C blocks to communicate with I2C based devices.
• Using the I2C Bus to Access Sensors
  This example shows how to use the I2C blocks to communicate with I2C based devices.
• Using SPI to Read and Write Data to SPI EEPROM
  This example shows how to configure and use SPI blocks to read and write data.
• Inter-Processor Communication Using IPC Blocks
  This example shows how to use the IPC blocks to communicate between multiple cores of multi-core of Texas Instruments™ C2000™ processors using Simulink® models.
• Modify Duty Cycle of ePWM Using DMA
  This example shows how to configure the direct memory access (DMA) parameters to modify the ePWM duty cycle.
• MAT-file Logging on SD Card for Texas Instruments C2000 Processors
  This example shows you how to perform MAT-file logging using Simulink® model on a Micro SD card mounted on Embedded Coder® Support Package for Texas Instruments™ C2000™ Processors.
• Using Sigma Delta Filter Module (SDFM) to Measure the Analog Input Signal
  This example shows how to use the Sigma Delta Filter Module (SDFM) to measure the analog input signal for Texas Instruments™ C2000™ processors.
• Using Comparator Subsystem (CMPSS) for Voltage Compare
  This example shows how to use the Comparator Subsystem (CMPSS) to compare the analog voltage signals for Texas Instruments™ C2000™ processors and monitor the status output.
• CAN Communication Using eCAN Blocks
  This example shows how to use the eCAN blocks to set up CAN communication between the target hardware and your host computer for Embedded Coder® Support Package for Texas Instruments™ C2000™ Processors.
• Use Embedded Coder blocks with SoC Blockset
  Use SoC Blockset™ pass-though block simulation with Embedded Coder^® Support Package for Texas Instruments™ C2000™ F28M3x Concerto™ Processors blocks.
• Serial Communication Using SCI Blocks
  This example shows how to use the SCI blocks to set up serial communication between the target hardware and your host computer for Embedded Coder® Support Package using the Texas Instruments™ C2000™ Processors.

Communication with Host

• Using CAN Calibration Protocol for Monitoring and Tuning
  This example shows how to use the CAN Calibration Protocol (CCP) block to monitor model signals and tune parameter values in the application code running on the target hardware.
• Parameter Tuning and Signal Logging with Serial Communication
  This example shows how to perform parameter tuning and data logging with a Simulink® model running in Texas Instruments™ C2000 targets.
• Serial Data Communication on F28M3x Concerto between ARM, C28x and the Host Computer
  This example shows you how to use Embedded Coder Support Package for Texas Instruments C2000 processors for serial data exchange between the host computer and the target as well as serial data exchange between the ARM and c28x core.
• Exchanging Ethernet Data with the F28M3x Concerto Processor
  This example shows you how to use Embedded Coder™ Support Package for Texas Instruments® C2000 Processors to send and receive UDP and TCP messages using the ARM Cortex-M3 core of F28M3x Concerto processor.
• Calibrate ECU Parameters from Third-party Calibration Tools Using XCP-based CAN Interface
  This example shows how to monitor signals and tune parameters of a Simulink model on Texas Instruments™ C2000™ board using XCP-based CAN Interface.
• Signal Monitoring and Parameter Tuning Over XCP-based CAN Interface
  This example shows how to monitor signals and tune parameters of a Simulink model on Texas Instruments™ C2000™ board using XCP-based CAN Interface.
• Code Execution Profiling on Texas Instruments C2000 Targets in XCP External Mode
  This example shows how to use Embedded Coder® Support Package for Texas Instruments™ C2000™ Processors to profile real-time execution of the generated code running as an executable on a Texas Instruments C2000 board with XCP on Serial and XCP on TCP/IP Interface.
• Signal Logging and Parameter Tuning in XCP External Mode with Packed Mode
  This example shows how to perform parameter tuning and data logging with a Simulink® model enabled with Packed Mode running on Texas Instruments™ C2000™ targets.

Applications

• Field-Oriented Control of PMSM with Quadrature Encoder Using C2000 Processors
  This example implements the field-oriented control (FOC) technique to control the speed of a three-phase permanent magnet synchronous motor (PMSM).
• Field-Oriented Control of PMSM with Hall Sensor Using C2000 Processors
  This example implements the field-oriented control (FOC) technique to control the speed of a three-phase permanent magnet synchronous motor (PMSM).
• Sensorless Field-Oriented Control of PMSM Using C2000 Processors
  This example implements the field-oriented control (FOC) technique to control the speed of a three-phase permanent magnet synchronous motor (PMSM).
• Open-Loop Control of 3-Phase AC Motors using C2000 Processors
  This example uses open-loop control (also known as scalar control or Volts/Hz control) to run a motor.
• Control PMSM Loaded with Dual Motor (Dyno) Using C2000 Processors
  This example uses field-oriented control (FOC) to control two three-phase permanent magnet synchronous motors (PMSM) coupled in a dyno setup.
• Partition Motor Control for Multiprocessor MCUs
  This example shows how to partition real-time motor control application on to multiple processors to achieve design modularity and improved control performance.
• Permanent Magnet Synchronous Motor Field-Oriented Control Using Concerto Processors
  This example shows how to control the speed of a three-phase Permanent Magnet Synchronous Motor in a closed-loop fashion via Field-Oriented Control using the C28x peripherals and MCB blocks from Motor Control Blockset™ library.
• Integrate MCU Scheduling and Peripherals in Motor Control Application
  This example shows how to identify and resolve issues with respect to peripheral settings and task scheduling early during development.
• Schedule a Multi-Rate Controller for a Permanent Magnet Synchronous Machine
  This example shows how to create a real-time executable for a Texas Instruments F28335 embedded target.
• Closed Loop Control of a DC-DC Buck Converter
  This example shows how to model a closed loop control of a DC-DC buck converter in the Embedded Coder® Support Package for Texas Instruments™ C2000™ Processors.
• Photovoltaic Inverter with MPPT Using Solar Explorer Kit
  This example shows how to implement a photovoltaic (PV) inverter system using the Embedded Coder® Support Package for Texas Instruments™ C2000™ Processors.
• Power Factor Correction Using Boost Converter
  This example shows how to implement power factor correction (PFC) using a boost converter with the Embedded Coder® Support Package for Texas Instruments™ C2000™ Processors.
• Interface LCD Booster Pack with Texas Instruments C2000 Processors
  This example shows how to configure and use the Kentec QVGA Display Booster Pack to display an image using C28x peripherals for Texas Instruments™ C2000™ processors.
• Digital DC/DC Buck Converter Using Peak Current Mode Control
  This example shows how to use the Comparator Subsystem (CMPSS) to regulate buck converter output voltage (BOOSTXL-BUCKCONV) using Peak Current Mode Control (PCMC) for Texas Instruments™ C2000™ processors.
• Read Position of BiSS-C Absolute Encoder
  This example shows how to read a position of an absolute encoder using the bidirectional serial/synchronous-continuous (BiSS-C) open protocol in the unidirectional mode.

Verification

• Code Verification and Validation with PIL
  This example shows you how to use Embedded Coder Support Package for Texas Instruments C2000 processor for code verification and validation using PIL.
• Real-Time Code Execution Profiling
  This example shows you how to use Embedded Coder™ Support Package for Texas Instruments C2000 Processors and Embedded Coder Support Package for Texas Instruments C2000 F28M3x Concerto Processors for real-time execution profiling of generated code.
• Code Verification and Validation with External Mode
  This example shows you how to use Embedded Coder Support Package for Texas Instruments® C2000 Processors for code verification and validation using External mode.
• Code Verification and Validation with PIL on the ARM Cortex M3 Core of the F28M3x Concerto Processor
  This example shows you how to use Embedded Coder Support Package for Texas Instruments C2000 Processor for code verification and validation using PIL.