Respondida
Simscape - transforming a rotational motion into an oscillating transational motion
The problem with this system is the singular configurations (theta=0 or 180deg). SimMechanics is better suited to simulate such ...
Simscape - transforming a rotational motion into an oscillating transational motion
The problem with this system is the singular configurations (theta=0 or 180deg). SimMechanics is better suited to simulate such ...
más de 12 años hace | 0
Publicado
Don’t Engineer The Hyperloop in a Vacuum
Since it was released in August, the Hyperloop proposal by Elon Musk generated a lot of interest. Reactions were both...
más de 12 años hace
Respondida
How can I put a signal (angle) on a joint actuator
This should help: http://blogs.mathworks.com/seth/2012/02/01/applying-motion-to-simmechanics-models/
How can I put a signal (angle) on a joint actuator
This should help: http://blogs.mathworks.com/seth/2012/02/01/applying-motion-to-simmechanics-models/
más de 12 años hace | 1
| aceptada
Publicado
Methods of the MATLAB System Block
In the last post on MATLAB System block, I tried to provide a basic introduction to System Objects in MATLAB and Simulink...
más de 12 años hace
Respondida
Is it possible to visualize reaction forces in the SimMechanics Mechanics Explorer?
Not possible... but it is a good suggestion, I'll report to our development team.
Is it possible to visualize reaction forces in the SimMechanics Mechanics Explorer?
Not possible... but it is a good suggestion, I'll report to our development team.
más de 12 años hace | 1
| aceptada
Respondida
Compiled Simulink model giving different results
I would bet that this is related to the "Single output/update function" parameter. See this doc page: http://www.mathworks.co...
Compiled Simulink model giving different results
I would bet that this is related to the "Single output/update function" parameter. See this doc page: http://www.mathworks.co...
más de 12 años hace | 0
| aceptada
Publicado
slLinearizer: Batch Linearization of Simulink Models
This week I am happy to welcome guest bloggers Charu Fadnavis and Erman Korkut to introduce the new slLinearizer interface...
más de 12 años hace
Respondida
how can i see variable output in subsystem on the surface of mask?
You will need an event listener or MATLAB S-Function to do a set_param on the mask drawing at every simulation step. I do not...
how can i see variable output in subsystem on the surface of mask?
You will need an event listener or MATLAB S-Function to do a set_param on the mask drawing at every simulation step. I do not...
más de 12 años hace | 0
Respondida
How can I stop my Simulink model from generating slprj folder and .mex* files?
What the link below says about those files is "exclude them from source control". It does not say that they are detrimental in g...
How can I stop my Simulink model from generating slprj folder and .mex* files?
What the link below says about those files is "exclude them from source control". It does not say that they are detrimental in g...
más de 12 años hace | 3
Publicado
From Symbolic to Simulink
I am recently visited the MathWorks Japan office and learned about interesting work done by my colleague Hitoshi...
más de 12 años hace
Publicado
2013 Simulink Student Challenge – Win up to $1000!
Have you done something super-cool in Simulink?Can you make a short video of it and share it on YouTube?Are you a...
más de 12 años hace
Respondida
Simulink Error "Derivative input -47 ..." with integrator block
The port "-47" is a bug. I would recommend recommend trying in R2013b (I think it is fixed in this latest release). Also, you ca...
Simulink Error "Derivative input -47 ..." with integrator block
The port "-47" is a bug. I would recommend recommend trying in R2013b (I think it is fixed in this latest release). Also, you ca...
más de 12 años hace | 0
| aceptada
Publicado
The MATLAB System Block
In R2013b, you will notice a new block in the Simulink Library Browser: The MATLAB System block. System...
más de 12 años hace
Resuelto
Find the sum of all the numbers of the input vector
Find the sum of all the numbers of the input vector x. Examples: Input x = [1 2 3 5] Output y is 11 Input x ...
más de 12 años hace
Publicado
Welcome R2013b!
MATLAB R2013b is live for download on MathWorks.com. Here is a list of Simulink-related features I find particularly...
más de 12 años hace
Publicado
Implementing an iterative algorithm using the While Iterator Subsystem
Last week I helped a user implementing an iterative algorithm in Simulink using the While Iterator Subsystem. I thought it...
más de 12 años hace
Respondida
Simulink:Aerospace 6 DoF Model Singularity with High Altitudes
I do not think it is because of high altitude. Based on the subsystem where the error happens shown in the screenshot, it looks ...
Simulink:Aerospace 6 DoF Model Singularity with High Altitudes
I do not think it is because of high altitude. Based on the subsystem where the error happens shown in the screenshot, it looks ...
más de 12 años hace | 0
Respondida
i want to make an subsystem on or off depend on the condition
See this: http://blogs.mathworks.com/seth/2012/04/09/conditional-execution/
i want to make an subsystem on or off depend on the condition
See this: http://blogs.mathworks.com/seth/2012/04/09/conditional-execution/
más de 12 años hace | 1
Respondida
pulse block in conditional subsystem
Change the Pulse Generator from Time-Based to Sample-based. That way the block will take a fixed-step size and the error should ...
pulse block in conditional subsystem
Change the Pulse Generator from Time-Based to Sample-based. That way the block will take a fixed-step size and the error should ...
más de 12 años hace | 0
Publicado
A Logic Analyzer for MATLAB and Simulink
When I wrote a post about the new features available in MATLAB R2013a, I got a request to provide details on the new Logic...
más de 12 años hace
Respondida
Variant Subsystem variant control condition defined by previous subsystem output
This is not what variant subsystems have been designed for. Use a if-else construct, a Switch, or other options like the ones I ...
Variant Subsystem variant control condition defined by previous subsystem output
This is not what variant subsystems have been designed for. Use a if-else construct, a Switch, or other options like the ones I ...
más de 12 años hace | 1
| aceptada
Respondida
Sampling time must agree
Blocks inside Stateflow Simulink functions must inherit their sample time. This is because there is no way for the engine to kno...
Sampling time must agree
Blocks inside Stateflow Simulink functions must inherit their sample time. This is because there is no way for the engine to kno...
más de 12 años hace | 0
| aceptada
Publicado
Referencing Configuration Sets for Model Reference
A few weeks ago I described the possibility of storing more multiple configuration sets in a single model. Today we will...
más de 12 años hace
Respondida
Using variable size matrices in Simulink
You are going in the wrong direction. Going back in the workspace is not the good approach. Instead, create a vector in Simul...
Using variable size matrices in Simulink
You are going in the wrong direction. Going back in the workspace is not the good approach. Instead, create a vector in Simul...
más de 12 años hace | 0
| aceptada
Respondida
Implementing a customised counter in SIMULINK using basic blocksets
I would use the discrete time integrator (or the equivalent using Sum and Unit Delay). If the input is zero, it will stay at zer...
Implementing a customised counter in SIMULINK using basic blocksets
I would use the discrete time integrator (or the equivalent using Sum and Unit Delay). If the input is zero, it will stay at zer...
más de 12 años hace | 0
Respondida
Why is matrix size changing after demux in simulink?
Use a Selector, this will give you a better control over the dimensions.
Why is matrix size changing after demux in simulink?
Use a Selector, this will give you a better control over the dimensions.
más de 12 años hace | 0
Respondida
SimMechanics - Spherical Joint "kinematic constraint cannot be maintained"
Open the loop by removing one of the joints. Then connect one sensor on each CS that was connected to the loop. Simulate for 0 s...
SimMechanics - Spherical Joint "kinematic constraint cannot be maintained"
Open the loop by removing one of the joints. Then connect one sensor on each CS that was connected to the loop. Simulate for 0 s...
más de 12 años hace | 1
Publicado
A Tweeting S-Function for the Raspberry Pi
I recently bought a Raspberry Pi. After trying a few of the demos included with the Simulink support package for Raspberry...
más de 12 años hace
Respondida
Create an internal loop in Simulink simulation
It looks like you need the While Iterator Subsystem: http://www.mathworks.com/help/simulink/slref/whileiteratorsubsystem.html...
Create an internal loop in Simulink simulation
It looks like you need the While Iterator Subsystem: http://www.mathworks.com/help/simulink/slref/whileiteratorsubsystem.html...
más de 12 años hace | 0
Respondida
A resettable Delay in SIMULINK
If you signal is discrete, the Delay block allos you to delay it form a number of samples coming form an input signal: http:/...
A resettable Delay in SIMULINK
If you signal is discrete, the Delay block allos you to delay it form a number of samples coming form an input signal: http:/...
más de 12 años hace | 1