Respondida
Hydraulics Circuit with load
I believe the confusion may come from the fact that in Simscape there is no gravity implied, unless Simscape Multibody is involv...

más de 3 años hace | 0

Respondida
Gas accumulator initial pressure
The volume in the initial condition (Variables tab) is supposed to be the volume of the liquid. Not sure about R2013a, but in m...

más de 3 años hace | 0

Respondida
ERROR Pressure fell below zero SimHydraulic
Pressure below zero error occurs most likely when the liquid is pulled through an orifice/resistance/pipe/valve or forced to exp...

casi 4 años hace | 0

Respondida
How to make assembly between induction motor,centrifugal pump and open/close valve for tank in simulink. Please guide to work out my query
There are a few blocks in Simscape Fluids that you can use to model the tank https://www.mathworks.com/help/physmod/hydro/ref/t...

casi 4 años hace | 0

Respondida
How can I get the Parameters for Contact stiffness and contact damping
Not sure about the RIGHT way to do this, but here is my two-step approach: 1. set a reasonable stiffness: set up the model to a...

casi 4 años hace | 0

Respondida
HOW could I add a tilt actuator in Simulink project.
This can be best handled by using Simscape Multibody and Simscape Fluids together. Some examples in the documentation: https:/...

casi 4 años hace | 0

Respondida
Why the dry air enthalpy in simscape perfect gas model is 420 ? It should be 293
I believe it depends on where 0 kJ/kg specific enthalpy is defined. In Simscape, looks like it's defined such that at 0K, h=0...

casi 4 años hace | 0

| aceptada

Respondida
Modelling a Pressure Reducing Valve
If you have access to Simscape Fluids add-on library, a pressure reducing valve block is available in the Hydraulic domain since...

casi 4 años hace | 0

Respondida
How can I simulate a Hydropnuematic suspension using simulink if the piston has a fixed orifice???
Something like this should work. Parameters and initial conditions will also be critical for the model to generate reasonable r...

casi 4 años hace | 0

Respondida
hydraulic pressure sensor and hydraulic flow rate sensors dont' work when used together
I suspect that you connected the sensors in series ... A pressure sensor is a sensor for an "across variable", so it's always m...

casi 4 años hace | 0

Respondida
Two-Phase Steam Flow Control
9+ years after the question was asked: It sounds like this application can be best handled using the two-phase fluid domain, wh...

casi 4 años hace | 0

Respondida
why have i this error: "Number of equations exceeds number of variables."
10 years after when the question was asked ... the thermal liquid domain should be able to handle the thermal+hydraulic applicat...

casi 4 años hace | 0

Respondida
how to design hydraulic actuator for suspension system?
Attempt to answer from 10 years later .... lol I suggest you use Simscape Multibody to model the mechanical part of the suspens...

casi 4 años hace | 0

Respondida
Demos of SimHydraulics on Matlab R2010a
Try this page for documentations in different versions: https://www.mathworks.com/help/doc-archives.html Then navigate to the r...

casi 4 años hace | 0

Respondida
Simulation of Cooling Towers using Matlab
A quick answer is yes. The main challenge I think is the find a correlation that works for YOUR cooling tower. The info in the ...

casi 4 años hace | 0

Respondida
Solenoid Valves Controlled With Simhydraulics
Thoughts on a few issues you may encounter building such a model and how to resolve them: 1. model the air bag. The volume and...

casi 4 años hace | 0

Respondida
Can I simulate this simple rod pump in SimHydraulics?
In its simplest form, I think a rod pump can be conceptualized as a single-acting cylinder with two check valves. One check val...

casi 4 años hace | 0

Respondida
How to get RC circuit parameter for equivalent circuit diagram from measurement Graph?
Simscape user here. So first, I would build the thermal network using the thermal domain. It's just a few thermal resistance a...

más de 4 años hace | 2

| aceptada

Respondida
co-simulation within Simulink
It sounds to me that the easiest way is to set up two Simulink simulations. Save the output from the 1st one to the MATLAB work...

más de 4 años hace | 1

Respondida
Missing something in Simscape.
The force sensor is a sensor for "through variable", so you'll need to connect in series with the element on which you'd like to...

más de 4 años hace | 0

Respondida
How can solve this error: Output 'Taout' declared with unit expression that contains an affine unit: 'degC'. Affine units are not allowed when declaring members of this type.
Declare temperatue units in K. That's what the error message is saying. The numerical value of the temperature may be overridd...

más de 4 años hace | 0

Respondida
Ideal Check Valve (Thermal Liquid, Simscape)
Hi Mash, Having a check value (or any closed valve) with absolutely zero leakage is in general a bad idea. It basically change...

más de 4 años hace | 1

Respondida
I'm not getting an expected temperature/pressure output from cooling a 600 [F] copper object [FEEDBACK REQUEST]
Looks like the convective coefficient was too small. Also, since the pipe has a wall model for heat transfer, you may not need ...

más de 4 años hace | 0

| aceptada

Respondida
What does "delta_vel_pos_AI" in Pipe (G) means?
Hi PY, The term is using a trick to avoid using the abs() function, which may otherwise trigger frequent zero-crossing when mdo...

más de 4 años hace | 0

| aceptada

Respondida
Is this an appropriate way to model the pressure/temperature drop across an elbow joint? Critiques requested
Hi AJ, There is a custom block for an elbow in thermal liquid domain that I can share. Could you please submit a Technical Sup...

más de 4 años hace | 0

| aceptada

Respondida
simscape block node arrangement
Don't know much about IGBT but this seems to be Simscape language syntax. After the "subcircuit2ssc" function, an object for ss...

más de 4 años hace | 0

| aceptada

Respondida
Trying to export .slx and its associated files to allow me to work from a faster PC.
In each of the file solid blocks, the path to the .step file is usually absolute. That full path can be different when you move...

más de 4 años hace | 0

Respondida
How to compile a simscape model (to dll) with tunable parameters?
Hi Bruno, Try this: make the parameter you want to tune in the generated code a "Simulink variable", i.e. a variable in the Sim...

más de 4 años hace | 0

Respondida
Model contact forces in custom designed CAD using File Solid?
One possibility is adding "point cloud" to better model the contact: https://www.mathworks.com/help/physmod/sm/ref/pointcloud.ht...

más de 4 años hace | 0

Respondida
How can I consider the changing temperature of a copper object that is being cooled by coiling a pipe around the outside surface?
The heat transfer between solid objects are best represented by conductive components and thermal mass. I suspect the thermal m...

más de 4 años hace | 1

| aceptada