Respondida
Simulation of two phase fluid with Simscape - pressure behavior unexplicable
Hi Marcel, The port area parameter of the Receiver Accumulator block doesn't affect the pressure drop between inside and outsid...

casi 2 años hace | 0

| aceptada

Respondida
MATLAB/Simulink/Simscape:Contact force analysis
You can only to "Convex Hull" for generic geometry (e.g. a stp file). It may or may not be good enough for your contact force m...

casi 2 años hace | 0

| aceptada

Respondida
The Excavator Hydraulic Jack Forces are Changing Direction in Simscape Multibody
The way the joints are actuated and the joint forces are sensed for inverse dynamic analysis looks OK. As a position signal is ...

casi 2 años hace | 1

| aceptada

Respondida
Fluid inertia in Simscape hydraulic
Hi Amodio, I don't think the actuator blocks model the inertia of the fluid inside. The "cushion" can be used to model some en...

casi 2 años hace | 0

Respondida
Center of mass of a free-floating body in Simscape Multibody is moving with no external forces
I believe there can be many solutions that would satisfy the initial conditions you have set. The only target set here is the s...

casi 2 años hace | 0

| aceptada

Respondida
Flow rate discrepancy between upstream and downstream of orifice model.
A diffential pressure 2950 psi sounds big enough to change the density of the fluid. As the density changes, volumetric flow ra...

casi 2 años hace | 0

Respondida
Simscape Fluids model of closed system
Hi Jeremy, Looks to me like an initialization issue. I don't have R2020b on my computer so I tried this on R2021b, the oldest ...

casi 2 años hace | 0

Respondida
How to make a revolute joint turn in one direction in Simscape?
There may be better solutions, but just some ideas. If you have access to Simscape Driveline, there is a one-way clutch (Unid...

casi 2 años hace | 0

Respondida
Pressure drop of a two-phase fluid pipeline in simscape
You can view the Simscape code of the Pipe (2P) block, save a copy, and modify it to use a custom correlation if you like. Find...

casi 2 años hace | 0

| aceptada

Respondida
Can "pipe(G)" block be used to model forced air convection?
I think it's possible. The combination of cross section and hydraulic diameter will give you a circumference; that multiplied b...

casi 2 años hace | 0

| aceptada

Respondida
HOW CAN I TURN AN EQUATION INTO COMPONENT IN A LIBRARY?
Hi Usha, In addition to Ayush's answer, I suggest that you look at the source code of a translational spring block. You custom...

casi 2 años hace | 1

Respondida
How does simscape caculate the hydraulic pressure?
The pump blocks in Simscape Fluids models the flow rate at different pressure difference and speed, but themselves are "volume-l...

casi 2 años hace | 0

Respondida
state flow入门之旅中的诸多疑问
应该是workspace的问题，红色阴影表示有缺失的参数值。Simulink模型的参数可能在 Base Workspace, Model Workspace 或者是 mask local workspace (你这里不会是最后这个情况)，可以参考这个文档：...

casi 2 años hace | 0

Respondida
Use Simscape parameter as variable in Simulink model
If it's in the Simscape Results Explorer, you should be able to use a Probe block to make it available during simulation as a Si...

casi 2 años hace | 0

Respondida
Using the TL-2P heat exchanger in simscape to simulate an external threaded tube heat exchanger
The way you set up the heat exchanger looks promising to me. I would use the Parameter Estimator App (Documentation) to estimat...

casi 2 años hace | 0

| aceptada

Respondida
why are the results different from moist air domain(MA) using only dry air and gas domain(G)? - simscape
Hello, Given the range of temperature you'd like to implement, I believe you are seeing the difference in the way the specific ...

casi 2 años hace | 1

Respondida
The sum of the 2 branches flow is different than pump flow
Hi Flavio, I looked at the model and below are my observations. the parameters and inputs for the pump look ridiculous: at 1m^...

casi 2 años hace | 2

| aceptada

Respondida
Simscape 4-Way 3-Position Directional Valve (IL) No "Fluids/Plot Valve Characteristics" Option
See the comment section for the discussion. Issue resolved (by itself) as of now.

casi 2 años hace | 0

Respondida
Pipe (TL) fluid compressibility problem
See this related question for a more detailed discussion: https://www.mathworks.com/matlabcentral/answers/2111661-rservoir-tl

alrededor de 2 años hace | 0

| aceptada

Respondida
Rservoir (TL)
Hi Karim, I did a few things that feel like best practices to me: (1) add a Tank (TL) block to where the reservoir was. Pleas...

alrededor de 2 años hace | 0

| aceptada

Respondida
Heat Exchanger (TL-TL) breaking thermodynamics?!
This shouldn't happen for parallel-flow heat exchangers, because of 2nd law of thermo-dynamics. But this may happen for counter...

alrededor de 2 años hace | 1

| aceptada

Respondida
hydraulic circle for fire suppression system clean agent
Hi Albara, It will be helpful if you could provide some schematic to show the interior of the agent tank so we can understand t...

alrededor de 2 años hace | 0

Respondida
Simscape Gas Inertia block
Hi Caleb, "Fluid inertia is negligible." is one of the model assumption of the Pipe (G) block. You may be able to modify the c...

alrededor de 2 años hace | 0

Respondida
Simscape fixed displacement pump pressure gain wrong?
Hi Sandro, one quick thing to fix: you need another reservoir at port B, otherwise the fluid has nowhere to go. The reservoir a...

alrededor de 2 años hace | 0

Respondida
Modeling a pressurized flexible body (balloon) in simscape multibody/fluids
Hi Siril, I feel the problem may be way more complicated than just "the two open red open wires". To model this pressurized fl...

alrededor de 2 años hace | 0

| aceptada

Respondida
Isothermal Fluids Pump/Motor Case Drain
Hi Philip, I feel the way you model it is very reasonable. Adding an small orifice or check valve mimics what happens in real ...

alrededor de 2 años hace | 0

Respondida
Changing Thermal Liquid Properties in Simscape
If you'd like to manually set the properties like density, Cp, etc., the right block to use is "Thermal Liquid Settings (TL)" fr...

alrededor de 2 años hace | 0

Respondida
Failed to increase pressure of a system with an actuator. Whats wrong?
It looks like that you would like to move the piston & mass so the pressure in Chamber A of the actuator will increase and you a...

alrededor de 2 años hace | 0

| aceptada

Respondida
Simscape piston moves without pressure difference
You don't need a force to keep a mass moving at constant velocity, as the acceleration is zero and F=m*a. When I add a damper...

alrededor de 2 años hace | 0

| aceptada

Respondida
Simscape pipe cleaning model - cleaning used pipe's interior surface with different fluid
It's possible to model a "solution", i.e. thermal liquid + passive scalar(s), using a quick-and-dirty way or a more formal one. ...

alrededor de 2 años hace | 0