Respondida
embedded coder cant generate reuseable function
Hi @chen lan, I understand that Embedded Coder generating multiple functions instead of reusing a single function for your reus...

11 meses hace | 0

Respondida
Parameter Estimation of a servo motor does not track well.
Hi @ashanni sonny, I understand that you are facing challenges in accurately modelling the servo motor’s behaviour. The issue s...

11 meses hace | 0

| aceptada

Respondida
Power measurement (electric motor)
Hi @Jack Daniels, To measure the active power, reactive power, apparent power, and power factor for your three-phase motor simu...

11 meses hace | 0

Respondida
Power Electronics Simulation Onramp Model Fidelity Part Bugged
Hi @Furkan, I couldn't able to reproduce the issue, it is working fine from my end. If it still persists you can refer to th...

11 meses hace | 0

| aceptada

Respondida
C2000 Synchronization of ePWM modules with external signal
Hi @Roberto, To configure ePWM1, ePWM2, ePWM3, and ePWM4 for synchronization using an external signal connected to GPIO40, you...

11 meses hace | 0

Respondida
Three phase dynamic load fails earlier than expected
Hi @Despoina Papageorgiou, I understand that you are facing an issue with the Three-Phase Dynamic Load in your Simulink model,...

11 meses hace | 0

Respondida
BlockIO output set to zero when multiple blocks are used
Hi @Aaron Troll, I understand you are facing issues with Simulink blocks generated by the IO Device Builder app, where multiple...

11 meses hace | 0

Respondida
How can I remove this warning:Estimated channel modulation for data extrapolation must be greater than zero. Use linear extrapolation.
Hi @Ignacio, I understand that you are facing an extrapolation error while simulating N Channel MOSFET model. The issue arise...

11 meses hace | 1

| aceptada

Respondida
Can I give Modulated Sine Wave as Input to CMPA of ePWM Block in MATLAB Simulink for SVPWM Generation ?
Hi @PANDIT DHANRAJ SURESH I understand that you are working on a 3-phase inverter using the TI Delfino F28379D LaunchPad and a...

11 meses hace | 0

Respondida
Pi Control plant cannot be linearized
Hi @Muhamed Ehab The errors "Subscript no. 2 is out of range" and "Plant cannot be linearized" occur because your model include...

11 meses hace | 0

Respondida
How to generate a stationary car and define the direction of the vehicle via matlab in Roadrunner
Hi @Xinyu Yang I understand that you want to import stationary vehicles into RoadRunner and ensure they are oriented parallel t...

11 meses hace | 0

Respondida
modeling an advanced energy management system for electric vehicles using MATLAB/Simulink
Hi Salih, To model your advanced energy management system (EMS), for electric vehicle you can follow the below steps: Firstly...

11 meses hace | 1

Respondida
problems encountered in DDPG.
Hi 邓龙京, The error message “Number of input layers for state-action-value function deep neural network must equal the number of...

11 meses hace | 0

Respondida
Error in rl.agent.AbstractAgent/train while executing example "Train Reinforcement Learning Agent in MDP Environment"
Hi @David Carrasco Martínez, I understand that you are facing an issue when “doTraining” flag is set to “true” in "Train Reinf...

11 meses hace | 0

Respondida
Train a DQN Agent: RL Simulink with Simscape (Error: Discontinuities detected within algebraic loop)
Hello, I understand that you are trying to replace a PI controller with a DQN agent for your Buck Converter model and encounte...

12 meses hace | 0

Respondida
get error runing TrainTD3AgentForPMSMControlExample.mlx
Hi @hai hu, I understand that you are facing an issue in the "TrainTD3AgentForPMSMControl" example model when “doTraining” fla...

12 meses hace | 0

Respondida
I am finding it difficult to design a 50MW VSC PV inverter.
Hi Prithwi, I understand that you are facing an issue in obtaining the desired output power. You can try the below suggestions...

12 meses hace | 0

Respondida
Error in solver configuration
Hi Pranjali, The error message "Input voltage must be greater than or equal to zero" suggests that your DC-DC converter is rec...

12 meses hace | 0

Respondida
Simscape Electrical: access "Display Assosciated Initial Conditions" programmatically
Hi Fredrik, To automatically set initial conditions for multiple synchronous machines using load flow results, you can follow ...

12 meses hace | 0

Respondida
Simulink stepper motor control
Hi Zsombor, To achieve continuous motor control independent of Simulink's sample time, you can use hardware interrupts or time...

12 meses hace | 0

Respondida
how can we plot the voltage trajectory of pmsm motor , when we have vd and vq data from simulink?What kind of plot is this?
Hi Deepak, To plot the voltage trajectory of a Permanent Magnet Synchronous Motor (PMSM) using the data from Simulink, you ...

12 meses hace | 0

Respondida
How to change SPWM Frequency of Arduino mega 2560 with MATLAB SIMULINK
Hi yahya, The output pulses from your Simulink model appears to be generated with frequency of "sin wave" so this is why the a...

12 meses hace | 0

Respondida
Simulink model control servo by mpu9250
Hi Aseel, To control servo motor using one of the yaw, pitch, or roll angles derived from your MPU9250 sensor in Simulink, you...

12 meses hace | 0

Respondida
PSCAD, Matlab interfacing
Hi Mohamed, To synchronize the timing of your MATLAB script with the PSCAD simulation, you need to ensure that your MATLAB cod...

12 meses hace | 0

Respondida
What is the best method to model or utilize the built-in model for a three-phase voltage regulator in MATLAB Simulink, specifically for the IEEE 34 distribution network?
Hi Asi, To model a three-phase voltage regulator in MATLAB Simulink for the IEEE 34 distribution network and with load flow an...

12 meses hace | 0

Respondida
detect and remove motion artifacts from ppg signal using lms adaptive filter
Hi Rajesh, I understand that you are looking for a method to remove noise from motion artifacts in a PPG signal. You can fol...

12 meses hace | 0

Respondida
Failed to load OpenDRIVE data: Failed to convert '-'
Hi, It looks like you are facing an error because there is an invalid character, like '-' where a number should be, in your fi...

12 meses hace | 0

Respondida
How to connect simpowersystem generic battery block to the simscape blocks without an algebraic loop error?
Hi Yurdakul, I understand that you are trying to connect a SimPowerSystems battery block to Simscape components and faci...

12 meses hace | 0

Respondida
Synchronous machine model incorrectly initializes when taking into account saturation
Hi Solis, I understand that you are facing an issue with the initialization of a synchronous machine model when accounting for...

alrededor de 1 año hace | 1

| aceptada

Respondida
how can i account charge and discharge of battery in ev modeling.
Hi Gokarna, I understand that you are trying to model both the charge and discharge behaviour of a battery in an electric vehi...

alrededor de 1 año hace | 0