Respondida
Latency not working when platform is the target
Hey @Carlos, I was facing the same issue with MATLAB R2024a, and I have been using a similar workaround. I have upgraded to MA...

más de 1 año hace | 0

Respondida
Drone Project Accelerometer/Gyroscope Implementation
Hey @Methmika, The 'IMU' block in Simulink, bundles the accelerometer, gyroscope, and magnetometer into one block. You can l...

más de 1 año hace | 0

Respondida
Adsorption process in Simulink
Hi @Ababacar Thiam, To switch between the two subsystems (adsorption and desorption) based on a control signal, the ‘Switch’...

más de 1 año hace | 0

| aceptada

Respondida
g = decsg() multiple objects
Hi @Bastiaan, The unexpected result is due to the set formula being passed to the ‘decsg’ function. The attached example code...

más de 1 año hace | 0

Respondida
Trajectory of a 3d body
Hi Rakshit, In the code shared, I am assuming that 'theta' is the pitch angle of the projectile,'alpha' is the angle of attack,...

más de 1 año hace | 0

| aceptada

Respondida
Input and State Constraints in MPC problem solved by quadprog
Hi Angelo, The following procedure can be used to convert the state constraints into input constraints. Consider the discret...

más de 1 año hace | 0

Respondida
Problem returning arrays from a C Caller in Simulink
Hi Julien, I comprehend that you are trying to obtain a time-varying output from a “C Caller” block. This can be achieved in ...

más de 1 año hace | 0

| aceptada

Respondida
"Solver was unable to reduce the step size without violating the minimum step size value" in Simscape simulation
Hi David, The warning "Solver was unable to reduce the step size without violating the minimum step size value" could arise ...

más de 1 año hace | 0

Respondida
How do I track the centroid of a set of frames in simscape multibody?
Hey dst, I understand that your main objective is to create a frame in “Simscape Multibody” located at the centroid of few o...

más de 1 año hace | 0

| aceptada

Respondida
How can I add an XYplot to Simulink Data Inspector programmatically ?
Hello Pavan, I comprehend that you are trying to plot XY data from MATLAB on the “Simulink Data Inspector”. There are couple of...

más de 1 año hace | 1

Respondida
How to get acceleration plot ? floor acceleration , driver acceleration
Hello Abdullah, From the shared screenshot I comprehend that the displacements of the floor and driver are available, and th...

más de 1 año hace | 0

Respondida
Error in Modeling and Simulation of an Autonomous Underwater Vehicle matlab exemple
Hello Samuel, I am able to replicate the error, “Error in port widths or dimensions” arising when running the “Modeling and...

más de 1 año hace | 0

Respondida
Configuring 2x2 Antenna Setup with 2 CSI-RS Ports in MATLAB's 5G Toolbox for CQI Reporting Test Compliance
Hi Jake, I understand that you are facing errors when trying CSI-RS and antenna panel configuration that are not mentioned in ...

más de 1 año hace | 0

Respondida
Coordinate system or axis system
Hey Sagar, I see that you are trying to create a body (a plane) in a 3D axis and then moving the body along a trajectory. Yo...

más de 1 año hace | 0

Respondida
There was a serious error in the calculation of the satellite position
Hello Ruizhe, From the code you have shared, I can comprehend that you are creating a satellite simulation using the “satelli...

más de 1 año hace | 1

Respondida
Expressions for QP matrices
Hello Elias, I understand that you are trying to use the “quadprog” function in the “Optimization Toolbox” to implement an MPC ...

más de 1 año hace | 0