Respondida
Switch in different Powergui
In Simscape Electrical, when you're using the Phasor simulation mode within the Powergui block, you are limited to certain compo...

10 meses hace | 0

Respondida
how do i implement direct torque control of induction motor without ac_4 block?
A good starting point for learning more about direct torque control is the documentation of Simscape Electrical: https://www.ma...

10 meses hace | 0

Respondida
How to control the speed of the synchronus motor in simscape?
In the attached image there is no control, it is open loop. For learning more about speed control of synchronous machines check ...

10 meses hace | 0

Respondida
Variable Speed Driver for Induction Motors - Constant V/Hz Control
Simscape Electrical provides a block implementing Scalar Control: https://www.mathworks.com/help/sps/ref/inductionmachinescalar...

10 meses hace | 0

Respondida
How to implement a V/Hz control transfer function in Simulink?
Simscape Electrical provides a block implementing Scalar Control: https://www.mathworks.com/help/sps/ref/inductionmachinescalar...

10 meses hace | 0

Respondida
Making a 3 phase semi-controlled converter using Simscape Electrical
In Simscape Electrical it is possible to use the Conveter (Three-Phase) block and set the 'Switching device' parameter to GTO or...

10 meses hace | 0

Respondida
is it possible to build a controllable load ?
In Simscape Electrical it is possible to use a dynamic load (single-phase or threee-phase). https://www.mathworks.com/help/sps...

10 meses hace | 0

Respondida
Where can we get description about HVDC control blocks?
If these blocks are part of a MathWorks product (e.g., Simscape Electrical) then you can click on help in the block mask to open...

10 meses hace | 0

Respondida
Having trouble charging battery using controlled voltage source
I would use a Controlled Current Source instead to charge the battery. See this simple Simscape Electrical example showing how t...

10 meses hace | 0

Respondida
Converting a sinusoidal signal into a trapezoidal one?
A saturation block can be used to saturate to sine wave so the output will look like a trapezoidal signal. Let’s say we have a s...

10 meses hace | 1

| aceptada

Respondida
DC-DC Buck-Boost Converter Closed Loop PWM control
The proportional control employed is not working properly. The controller is very basic, multiplying the error with a constant b...

10 meses hace | 0

Respondida
Undefined function 'cos' for input arguments of type 'char'.
inputdlg returns a cell array of character vectors containing one input per edit field, starting from the top of the dialog box....

10 meses hace | 0

| aceptada

Respondida
Why does SIMSCAPE have different values for the speed and the revolutions in the output, although they have to be the same? Is it maybe due to false parameters of the PI-regulator?
There are two issues with this model: i) instead of using electrical angle in the dq-abc block is using the mechanical angle, an...

10 meses hace | 0

Respondida
Dynamically simulate PMSM motor
The best starting point for understanding how the FEM-Parametrized PMSM block can be configured is the documentation page: http...

10 meses hace | 1

Respondida
Why PMSM model spins with SVPWM block?
In Simscape Electrical (or other Simulink toolboxes), the models for Permanent Magnet Synchronous Motors (PMSMs) can indeed star...

10 meses hace | 0

Respondida
How can I use the Battery Equivalent Circuit module and output its SOC？
It is possible to use a Probe block to output internal variables such as state of charge from the Battery Equivalent Circuit blo...

11 meses hace | 0

| aceptada

Respondida
How to measure the frequency of a 3 phase generator in simscape electrical
You can use a Sinusoidal Measurement (PLL, Three-Phase) block in Simscape Electrical. The Sinusoidal Measurement (PLL, Three-Pha...

11 meses hace | 1

| aceptada

Respondida
Switching and Conduction losses of MOSFET
lossesTable = ee_getPowerLossSummary(node) calculates dissipated power losses and switching losses for semiconductor blocks in a...

11 meses hace | 0

| aceptada

Respondida
how should I model the grid for the electrical supply for my Electrolyzer?(simscape)
Probably the best place to start is this example in Simscape Electrical: https://www.mathworks.com/help/sps/ug/green-hydrogen-m...

11 meses hace | 0

Respondida
Battery Short Circuit Current
That is the short circuit current. As there is no short circuit until 30s the current remains to 0 (Switch is open from 0 to 30s...

12 meses hace | 1

Respondida
how to make flux based model + inverter
This system can be modeled in Simscape Electrical with existing blocks (PMSM or FEM-Parameterized PMSM and Converter (Three-Phas...

12 meses hace | 0

Respondida
i need a model of synchronous machines with dampers windinf
Simscape Electrical offers synchronous machine models with both damper windings and without. For synchronous machines with damp...

12 meses hace | 0

Respondida
Automatic Transfer Switch Model
Simscape and Simscape Electrical provide the option to model a transfer switch. The easiest way is to use a circuit breaker (sin...

alrededor de 1 año hace | 0

Respondida
What can I learn from Mathway's "Three-Phase Systems and Machines"?
This page aims to show how to simulate a three-phase power system containing electrical machines and other three-phase models. ...

alrededor de 1 año hace | 0

Respondida
DC Microgrid modeling and control
Simscape Electrical is provinding many examples in the microdgrid area that can be used as a starting point. Check for example: ...

alrededor de 1 año hace | 0

Respondida
Matlab simulink file shows following error Simulink does not have enough information to determine output sizes for this block. If you think the errors below are inaccurate, try specifying types for the block inputs and/or sizes for the block outputs.
Taking a quick look there are two changes that are needed to make this model run: 1) Line 38 in the MATLAB function should be (...

alrededor de 1 año hace | 0

Respondida
Error with running a Simulink model.
Without the files is not easy to tell where the problem is. I suspect when you run the first model some parameters from the work...

alrededor de 1 año hace | 0

Respondida
Direct matrix converter with svm control
A good starting point is Simscape Electrical. You can check this example: https://www.mathworks.com/help/sps/ug/three-phase-mat...

alrededor de 1 año hace | 0

Respondida
How we modeling PWM inverter with PI and PR current controllers with grid connection
There is not such thing as the best controller. It all depends on specific requirements. For a starting point with grid connecte...

alrededor de 1 año hace | 0

Respondida
vector control of of WRSM ( wound rotor synchronous motor
From the diagram is difficult to spot the issue as everything is in a subsystem. I assume there is a sign mismatch somewhere. Fo...

alrededor de 1 año hace | 0