Respondida
How to increase acquisition frequency in real time? (TI Board F28379D)
Hi Jessé/Taimur, You can use the 2 model approach when running computation intensive algorithms at high sample rate for data lo...

alrededor de 7 años hace | 0

Respondida
How to measure control law execution time in Launchxl-F28379D?
Hi Enric, Attached is the model which helps you to achieve the same in simulink w.r.t GPIO bit activation and deactivation. Fe...

alrededor de 7 años hace | 0

| aceptada

Respondida
Embedded Coder for C2000
Hi Richard, Attached is the model which i found to be working for DAC-A. The model is created in 2018b version of MATLAB. I fo...

alrededor de 7 años hace | 0

Respondida
extra signals DMA example epm Duty Cycle
Hi Gauthier, That can complicate things as the DMA runs in steps of 1, picking next value from table until 500 such iterations ...

alrededor de 7 años hace | 0

| aceptada

Respondida
extra signals DMA example epm Duty Cycle
Hi Gauthier, As I mentioned, since the Master ePWM is configured to react on CMPA count and we update the same using DMA ch 1, ...

alrededor de 7 años hace | 0

Respondida
extra signals DMA example epm Duty Cycle
Hi Gauthier, I may need your model. Can you attach the up to date model.? Regards, Venkatesh C

alrededor de 7 años hace | 0

Respondida
extra signals DMA example epm Duty Cycle
Hi Gauthier, If you get 200 values in the duty cycle table then you may need to update the DMA configuration w.r.t this. We set...

alrededor de 7 años hace | 0

Respondida
extra signals DMA example epm Duty Cycle
Hi Gauthier, To implement deadband, please do the following. Keep all box un-checked for the ePWMxB as shown below as to produ...

alrededor de 7 años hace | 0

Respondida
extra signals DMA example epm Duty Cycle
Hi Gauthier, Keeping aside the operation of DMA in this example, we can synchronize the PWM output with help of following confi...

alrededor de 7 años hace | 0

Respondida
extra signals DMA example epm Duty Cycle
Hi, Please refer this video: https://in.mathworks.com/matlabcentral/fileexchange/49109-dual-motor-control-with-ti-launchxl-f28...

alrededor de 7 años hace | 0

Respondida
extra signals DMA example epm Duty Cycle
Hi Gauthier, You may not need other DMA's for generating rest of the PWM's. Once you have the First ePWM working, you can sync...

alrededor de 7 años hace | 0

Respondida
ADC SCI f28335 problem
Hi Samuel, It may be a good idea to contact us @ https://in.mathworks.com/support/contact_us.html. That can help us better und...

alrededor de 7 años hace | 0

Respondida
Modify Duty Cycle of ePWM Using DMA
Hi, Please can you run the command at the command prompt: >>which sineTableCalculation.m This will give you the path to the f...

alrededor de 7 años hace | 0

| aceptada

Respondida
ADC SCI f28335 problem
Hi Sam, Are you running the model in external mode? Can you try increasing the baudrate of the SCI and see if it helps. Ther...

alrededor de 7 años hace | 0

Respondida
TI C2000 code generation generates double data type functions instead of single ones
Hi, Please note that the CRL we support are meant to be used for fixed point math. These CRL's don't support float operations. ...

alrededor de 7 años hace | 2

Respondida
S-function works in normal mode but doesn't in external mode
Hi, Could run the model in external mode and could recieve only zero. I have not debugged the S-Function, but I can recommend ...

alrededor de 7 años hace | 0

Respondida
S-function works in normal mode but doesn't in external mode
Can you do a crtl+j and send the snap of Sample Time Legend that pop's up as below.

alrededor de 7 años hace | 0

Respondida
S-function works in normal mode but doesn't in external mode
Hi, When deploying the model on target we configure it for Fixed step disctere solver as the controller runs in discrete amount...

alrededor de 7 años hace | 0

Respondida
Build process completed successfully Error evaluating registered method 'Start' of MATLAB S-Function 'sserialcb' in 'TRANSMIT1/Serial Configuration'. Caused by: Open failed: Cannot connect to the COM6 port. Possible reasons are another application is
Hi, Please reach to us at: https://www.mathworks.com/support/contact_us.html Regards, Venkatesh C

alrededor de 7 años hace | 0

Respondida
how to execute SCI communication
Hi, Please can you attach the model or snapshots? Do you run one of them in external mode? How are you ensuring the communicati...

alrededor de 7 años hace | 0

Respondida
ExtTargetPktPending() call failed while checking for target pkt
Hi, A solution depends upon which controller is used, is it controlcard or launchpad? which version of the MATLAB like 2018x? ...

alrededor de 7 años hace | 0

Respondida
TMS320F28069M: File C:\ProgramData\MATLAB\SupportPackages\R2018b\toolbox\target\supportpackages\tic2000\registry\thirdpartytools\thirdpartytools_win64.xml not found
Hi, Could you please run the 'targetupdater' to configure the supportpackage first. Regards, Venkatesh C

alrededor de 7 años hace | 0

Respondida
Access multiple I2C sensors with C2000 and simulink
Hi, You may also look in to the implementation of the example model 'c28x_i2c_sensor' here we are sequencing the Tx and Rx oper...

alrededor de 7 años hace | 0

Respondida
Access multiple I2C sensors with C2000 and simulink
Hi, Please can you refer the example model ' c28x_i2c_eeprom_interrupt'. From this example model one can observe the use of C28...

alrededor de 7 años hace | 0

Respondida
TMS320F28335: Model for Simulink based buck converter control
Hi, Please let us know if this example works for you. The example would use the ADC and PWM module. https://in.mathworks.co...

alrededor de 7 años hace | 0

Respondida
C2000 eCAN bus-off condition
Hi, Adding the below line of code should help! HWREG(CANA_BASE + CAN_O_CTL) |= CAN_CTL_ABO; Regards, Venkatesh Chilapu...

más de 7 años hace | 0

Respondida
C2000 eCAN bus-off condition
Hi, We provide custom code blocks under simulink coder->custom code->System Initialize using which you may initialize the ABO b...

más de 7 años hace | 1

Respondida
[f28335] I2C transmit status
Hi, Please refer to below link: https://in.mathworks.com/help/supportpkg/texasinstrumentsc2000/ref/c28xi2ctransmit.html The s...

más de 7 años hace | 0

Respondida
I want to generate code for TI-Launchpad F28069M by using Simulink. Currently I am using Matlab2016b. Is it possible to genarate code for CCSv8 ? Can you provide me the steps I should follow ?
Please refer the below link for list of compatible CCS and MATLAB version. http://software-dl.ti.com/ccs/esd/documents/ccs_matl...

más de 7 años hace | 1

Respondida
while executing External Mode MEX-file 'ext_comm': ExtTargetPktPending() call failed while checking for target pkt? in c2000 F28379D launchpad Simulink,
Please update on the version of MATLAB being used.

más de 7 años hace | 1