Borrar filtros
Borrar filtros

Data to pdf report

6 visualizaciones (últimos 30 días)
Abbey Kirkman
Abbey Kirkman el 23 de Feb. de 2021
Respondida: Tesfaye Girma el 23 de Feb. de 2021
hi i would like my file names to show up in a table on my report please see my code below any help would be appraciated
%%Loading baseline data
[filename,pathname]=uigetfile('*.xlsx','Pick your baseline file');
if filename~=0
baseline_=readmatrix(fullfile(pathname,filename),'Range',17)
baseline=baseline_(:,4:37)
h={' Speed' 'Torque' 'TORQUE.ECE' 'POWER' 'ECE_power' 'BMEP' 'Correction_factor' 'Coolant_Temperature_Out_of_Engine' 'Coolant_Temperature_Into_Engine' 'Coolant_Pressure' 'Fuel_Pressure' 'Fuel_Temperature' 'Specific_Fuel_Consumption' 'Inlet_Air_Temperature' 'Humidity' 'Barometric_Pressure' 'Test_Cell_Temperature' 'Exhaust_Temperature_in_CAT' 'Exhaust_Temperature' 'Lambda' 'Exhaust_Pressure' 'Inlet_Manifold_Pressure' 'Blowby' 'Pedal_Position' 'IgnRetCyl1' 'IgnRetCyl2' 'IgnRetCyl3' 'IgnRetCyl4' 'ECU_Pedal_Position' 'Ignition_Timing' 'ThrottleAngle' 'Coolant_Temperature_ECU' 'Oil_Pressure_Head' 'Sump_Oil_Temperature' };
BASELINE_DATA=[h;num2cell(baseline)]
else
baseline=0;
end
%%Loading Data1 data
[filename1,pathname1]=uigetfile('*.xlsx','Pick your Data1 file');
if filename1~=0
data_1=readmatrix(fullfile(pathname1,filename1),'Range',17);
data1=data_1(:,4:37)
h={' Speed' 'Torque' 'TORQUE.ECE' 'POWER' 'ECE_power' 'BMEP' 'Correction_factor' 'Coolant_Temperature_Out_of_Engine' 'Coolant_Temperature_Into_Engine' 'Coolant_Pressure' 'Fuel_Pressure' 'Fuel_Temperature' 'Specific_Fuel_Consumption' 'Inlet_Air_Temperature' 'Humidity' 'Barometric_Pressure' 'Test_Cell_Temperature' 'Exhaust_Temperature_in_CAT' 'Exhaust_Temperature' 'Lambda' 'Exhaust_Pressure' 'Inlet_Manifold_Pressure' 'Blowby' 'Pedal_Position' 'IgnRetCyl1' 'IgnRetCyl2' 'IgnRetCyl3' 'IgnRetCyl4' 'ECU_Pedal_Position' 'Ignition_Timing' 'ThrottleAngle' 'Coolant_Temperature_ECU' 'Oil_Pressure_Head' 'Sump_Oil_Temperature'};
DATA1=[h;num2cell(data1)]
else
data1=0;
end
ect........
fprintf('baseline- %s \n 1-%s \n 2-%s \n 3-%s \n 4-%s \n 5-%s \n 6-%s ' ,filename,filename1,filename2,filename3,filename4,filename5,filename6)
%% essentiually i would like the line above to be shown in table form in my pdf report
  1 comentario
Tesfaye Girma
Tesfaye Girma el 23 de Feb. de 2021
publish('myfile.m','pdf')

Iniciar sesión para comentar.

Respuestas (1)

Tesfaye Girma
Tesfaye Girma el 23 de Feb. de 2021
publish('myfile.m','pdf')

Etiquetas

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by