Estadística
0 Preguntas
17 Respuestas
CLASIFICACIÓN
5.986
of 301.275
REPUTACIÓN
8
CONTRIBUCIONES
0 Preguntas
17 Respuestas
ACEPTACIÓN DE RESPUESTAS
0.00%
VOTOS RECIBIDOS
2
CLASIFICACIÓN
of 21.216
REPUTACIÓN
N/A
EVALUACIÓN MEDIA
0.00
CONTRIBUCIONES
0 Archivos
DESCARGAS
0
ALL TIME DESCARGAS
0
CLASIFICACIÓN
of 173.726
CONTRIBUCIONES
0 Problemas
0 Soluciones
PUNTUACIÓN
0
NÚMERO DE INSIGNIAS
0
CONTRIBUCIONES
0 Publicaciones
CONTRIBUCIONES
0 Público Canales
EVALUACIÓN MEDIA
CONTRIBUCIONES
0 Temas destacados
MEDIA DE ME GUSTA
Feeds
TMS320F28379D/TMS320F28335: How to do a five PWM signals with dead time and logic gates?
Hi @Lucas, You may need to use the c2000 ePWM (https://www.mathworks.com/help/ti-c2000/ref/epwmtype14.html) blocks to generate ...
10 días hace | 0
DRV8305EVM: nFault led
Hi, Could you please verify the ADC offsets and HALL calibration offset value. 1) You can run the open loop motor control exam...
10 días hace | 0
Increasing PWM frequency for Sensorless FOC Example
Hi Jarek, As you increase the PWM frequency, the controller sample time will reduce which may lead to an overrun. Please check ...
13 días hace | 0
Speed command spikes during host-controlled ramp on F28069M dual-motor dyno model
Hi Jonathan, 1) SCI blocks are driver blocks designed for discrete data streaming. You can get smotther ramp by reducing the sa...
13 días hace | 0
how to use two carriers for epwm1a module.
Hi Mandvi, Two carrier cannot be generated for a specific ePWM module in TI C2000 Processors. You may need to change the modula...
13 días hace | 0
Can we deploy Field-Oriented Control of PMSM Using Reinforcement Learning on TI F28379D LaunchPad ?
Hi Aizaz, OpenMP is not supported in TI C2000 devices. Check this post for more info: https://e2e.ti.com/support/microcontroll...
alrededor de 1 mes hace | 0
PMSM FOC Hall sensor input for custom GPIO pin configurations
Hi Bhagyesh, 1.ECAP inputs in F20049C are fed by Input X-BAR. Hence you can route any GPIO to eCAP inputs. In order to change ...
alrededor de 1 mes hace | 0
How can I create SPWM from ePWM blocks for C2000 in Simulink?
Hi, In Sinusoidal PWM, the pulse width will follow sinusoidal pattern i.e. it increases and reaches maximum and then starts r...
7 meses hace | 0
Missing EPWM features in C2000 Blockset
Hi Aditya, You can make use of Register Read/Write block to make the above register settings. Please check the below link for ...
9 meses hace | 0
TI F28379D Serial Communication to other Systems
Hi Timo, Please refer to the following example on serial communication: https://in.mathworks.com/help/ti-c2000/ug/serial-commu...
alrededor de 1 año hace | 0
How to switch off all 6 MOSFETs (6SO) with ePWM block from C2000 Motor Control Blockset?
Hi, You can ePWM trip zone unit to turn the ePWMs off. Hope this helps. Thanks, Mukul
más de 1 año hace | 0
How can I read analog COS and SIN voltages with LAUNCHXL-F28069M?
Hi, The example mentioned by you uses the TI TMDSRSLVR - Resolver EVM kit. This resolver uses a level shifter and a gain ampli...
más de 2 años hace | 0
MATLAB HARDWARE , EXTERNAL MODE
Hi, Please refer to the following motor control and power examples that are shipped along with C2000 Microcontroller Blockset: ...
más de 2 años hace | 0
CLA compliation issue usin F28388D on simulink 2022a
Hi Aniket, This issue comes if your model calls any math function inside CLA. Please check if there is any call to a math funct...
más de 2 años hace | 2
Simulink Texas Instruments F28388D CLAerror: cannot open source file "cla_header.h"
Hi Maximilian, cla_header.h is a header file where the signals and data stores to be stored in CLA storage classes are declare...
más de 4 años hace | 0
| aceptada
Error using the C2000 CLA
Hi Balint, The CLA does not support sine function and has its own sine function defined in CLAMath Library provided by TI. In ...
más de 4 años hace | 0
Simulink for Texas Instruments C2000 microcontrollers CLA: cannot open source file "cla_header.h" in the LAUNCHXL-F28379D
Hi Gabriel, cla_header.h is the file where the data stores, signals and states accesible by cla are declared. Could you please ...
más de 4 años hace | 0
