Matthew Mishrikey

Last seen: 9 meses hace | Con actividad desde 2021

Followers: 0 Following: 0

Estadística

Feeds

Pregunta

Simulink scope trace is grayed out
In simulink I have a scope with three inputs. The scope has 3 subplots. The first and third input have a mux in front, and ...

9 meses hace | 0 respuestas | 0

0

respuestas

Pregunta

Run an enabled and triggered subsystem only one time (single shot)
I have a Simulink enabled and triggered subsystem that I want to execute only one time. I think one way to do it is to make ...

9 meses hace | 1 respuesta | 0

1

respuesta

Pregunta

Simulink dashboard button matching
I'm looking for suggestions on how to approach a Simulink interface problem. In case 1 below, both dashboard buttons have con...

9 meses hace | 1 respuesta | 0

1

respuesta

Pregunta

A few basic Simulink/Simscape questions
In the past I've generally used Simulink simulations for short bursts of transient analysis. I was curious if it were possibl...

10 meses hace | 1 respuesta | 0

1

respuesta

Pregunta

Dynamic dashboard radio button options
Hello! I was curious if it was possible to make the options of a radio button change based on another radio button. This is ...

10 meses hace | 2 respuestas | 0

2

respuestas

Pregunta

variables with scope local to subsystem
I'm a bit confused about variable scope. I think I know what's going on but am looking for confirmation and maybe advice on th...

más de 3 años hace | 1 respuesta | 0

1

respuesta

Respondida
Radio Button Mask for Simscape Block
I figured out a way. I saw a snippet of code in one of the videos on the topic, and it gave me enough clues to write a callback...

más de 3 años hace | 0

| aceptada

Pregunta

Radio Button Mask for Simscape Block
I have a stock Simscape block (Cauer Element) that has two parameters - Resistance and Tau. I am trying to add a mask to modify...

más de 3 años hace | 1 respuesta | 0

1

respuesta

Pregunta

get_param fails with simscape block
Weird/unexpected behavior, not sure if it's a bug. I'm trying to use get_param to access a stock simscape thermal component. I...

más de 3 años hace | 1 respuesta | 0

1

respuesta

Respondida
Basic Slider Switch question
I think I figured out a way. I hope there's a better solution because this seems like a royal pain. 1) in the simscape compone...

más de 3 años hace | 0

Respondida
Basic Slider Switch question
I think I'm getting closer to an answer here. I setup slider switch to control a constant block, which feeds a data store wri...

más de 3 años hace | 0

Pregunta

Simscape Block Parameter not Tunable
I wish to control a Simscape block parameter using the dashboard slider switch. I select Temperature Source, but the slider swi...

casi 4 años hace | 1 respuesta | 0

1

respuesta

Pregunta

Simulink dashboard switch to control masked parameter
I wanted to have a slider switch control such that On position would make it 1 Ohm and off position would make it 5 ohms. The s...

casi 4 años hace | 1 respuesta | 0

1

respuesta

Respondida
Two circles geometry problems
Not clear from the second drawing what the dl of interest is. Let's assume dl is the distance between the left edge of each ci...

casi 4 años hace | 0

| aceptada

Respondida
Control Design Onramp with Simulink
Enter learning.simulink.launchOnramp('controls') in your MATLAB window.

casi 4 años hace | 2

Pregunta

Parameter Writer block not recognizing blocks
In image below I show a sim with a slider switch that modifies the constant block on the left. This the uses a goto/from block ...

casi 4 años hace | 1 respuesta | 0

1

respuesta

Respondida
Is there a way to nest transfer functions?
Okay, nevermind, found the solution is to use s = tf('s') rather than tf([num dem]).

casi 4 años hace | 0

| aceptada

Pregunta

Is there a way to nest transfer functions?
I wish to build up a transfer function inside a for loop such that each iteration builds up a new transfer function based on pre...

casi 4 años hace | 1 respuesta | 0

1

respuesta

Pregunta

Basic Slider Switch question
I was curious if it was possible to make a slider switch dashboard element control more than one block simultaneously. Alterna...

casi 4 años hace | 3 respuestas | 0

3

respuestas

Respondida
Simscape/Simulink persistent variable in algebraic loop
I think I managed to figure out a solution. As suggested elsewhere a delay block can "break" the algebraic loop. I needed thr...

casi 4 años hace | 0

| aceptada

Pregunta

Simscape/Simulink persistent variable in algebraic loop
I have a simple Simscape electrical model containg a circuit that trips if a current is exceeded. I want the trip to happen a c...

casi 4 años hace | 2 respuestas | 0

2

respuestas

Pregunta

Generate Zth transient thermal impedance curves with Simscape
Simscape has some nice thermal domain elements like Cauer thermal model elements. I was looking to generate a set of Zth curves...

casi 4 años hace | 1 respuesta | 0

1

respuesta

Pregunta

Trying to convert Kelvin to Celsius in Simscape code
I have a simulation with some Simscape Thermal and Electrical elements. The electrical element is a modification of the stock t...

casi 4 años hace | 1 respuesta | 0

1

respuesta

Pregunta

simscape block node arrangement
In the IGBT example here: https://www.mathworks.com/help/physmod/sps/ug/Troubleshoot-of-spice-nigbt-conversion.html the gener...

más de 4 años hace | 1 respuesta | 0

1

respuesta