This is machine translation

Translated by Microsoft
Mouseover text to see original. Click the button below to return to the English version of the page.

Note: This page has been translated by MathWorks. Click here to see
To view all translated materials including this page, select Country from the country navigator on the bottom of this page.

Tune 2-DOF PID Controller (PID Tuner)

This example shows how to design a two-degree-of-freedom (2-DOF) PID controller using PID Tuner. The example also compares the 2-DOF controller performance to the performance achieved with a 1-DOF PID controller.

In this example, you represent the plant as an LTI model. For information about using PID Tuner to tune a PID Controller (2DOF) block in a Simulink® model, see Design Two-Degree-of-Freedom PID Controllers (Simulink Control Design).

2-DOF PID controllers include setpoint weighting on the proportional and derivative terms. Compared to a 1-DOF PID controller, a 2-DOF PID controller can achieve better disturbance rejection without significant increase of overshoot in setpoint tracking. A typical control architecture using a 2-DOF PID controller is shown in the following diagram.

For this example, first design a 1-DOF controller for the plant given by:

G(s)=1s2+0.5s+0.1.

G = tf(1,[1 0.5 0.1]);
pidTuner(G,'PID')

Suppose for this example that your application requires a faster response than the PID Tuner initial design. In the text box next to the Response Time slider, enter 2.

The resulting response is fast, but has a considerable amount of overshoot. Design a 2-DOF controller to improve the overshoot. First, set the 1-DOF controller as the baseline controller for comparison. Click the Export arrow and select Save as Baseline.

Design the 2-DOF controller. In the Type menu, select PID2.

PID Tuner generates a 2-DOF controller with the same target response time. The controller parameters displayed at the bottom right show that PID Tuner tunes all controller coefficients, including the setpoint weights b and c, to balance performance and robustness. Compare the 2-DOF controller performance (solid line) with the performance of the 1-DOF controller that you stored as the baseline (dotted line).

Adding the second degree of freedom eliminates the overshoot in the reference tracking response. Next, add a step response plot to compare the disturbance rejection performance of the two controllers. Select Add Plot > Input Disturbance Rejection.

PID Tuner tiles the disturbance-rejection plot side by side with the reference-tracking plot.

The disturbance-rejection performance is identical with both controllers. Thus, using a 2-DOF controller eliminates reference-tracking overshoot without any cost to disturbance rejection.

You can improve disturbance rejection too by changing the PID Tuner design focus. First, click the Export arrow and select Save as Baseline again to set the 2-DOF controller as the baseline for comparison.

Change the PID Tuner design focus to favor reference tracking without changing the response time or the transient-behavior coefficient. To do so, click Options, and in the Focus menu, select Input disturbance rejection.

PID Tuner automatically retunes the controller coefficients with a focus on disturbance-rejection performance.

With the default balanced design focus, PID Tuner selects a b value between 0 and 1. For this plant, when you change design focus to favor disturbance rejection, PID Tuner sets b = 0 and c = 0. Thus, PID Tuner automatically generates an I-PD controller to optimize for disturbance rejection. (Explicitly specifying an I-PD controller without setting the design focus yields a similar controller.)

The response plots show that with the change in design focus, the disturbance rejection is further improved compared to the balanced 2-DOF controller. This improvement comes with some sacrifice of reference-tracking performance, which is slightly slower. However, the reference-tracking response still has no overshoot.

Thus, using 2-DOF control can improve disturbance rejection without sacrificing as much reference tracking performance as 1-DOF control. These effects on system performance depend strongly on the properties of your plant and the speed of your controller. For some plants and some control bandwidths, using 2-DOF control or changing the design focus has less or no impact on the tuned result.

See Also

Related Topics