Pin Slot Joint

Joint with orthogonal prismatic and revolute primitives

• 

Libraries:
Simscape / Multibody / Joints

Description

The Pin Slot Joint block models a joint with one translational and one rotational degree of freedom, as shown in the image.

The follower frame moves relative to the base frame in this sequence:

The follower frame moves along the x-axis of the base frame, and then rotates about the z-axis of the follower frame generated after the translation.

To specify the target of the initial state for a joint primitive, use the parameters under State Targets. The targets are specified in the base frame. You can also set the priority levels for the targets. If the joint is not able to satisfy all the state targets, the priority level determines which targets to satisfy first and how closely to satisfy them. For an example, see the Guiding Assembly section of How Multibody Assembly Works.

To model damping and the spring behavior for a joint primitive, use the parameters under Internal Mechanics. Use the Damping Coefficient parameter to model energy dissipation and the Spring Stiffness parameter to model energy storage. Joint springs attempt to displace the joint primitive from its equilibrium position, and joint dampers act as energy dissipation elements. The springs and dampers are strictly linear.

To specify the limits of a joint primitive, use the parameters under Limits. The lower and upper bounds define the width of the free region. The block applies a force to accelerate the joint position back to the free region when the position exceeds the bounds. The block uses a smoothed spring-damper method to compute the force. For more information about the smoothed spring-damper method, see the Description section of the Spatial Contact Force block.

The Force, Torque, and Motion parameters in the Actuation section control the motion of the joint primitives during simulation. For more information, see Specifying Joint Actuation Inputs. Additionally, the joint block has ports that output sensing data, such as position, velocity, acceleration, force, and torque, that you can use to perform analytical tasks on a model. For more information, see Sensing and Force and Torque Sensing.

To specify the joint mode configuration, use the Mode parameter. For more details, see Mode Configuration under the Ports and Parameters sections.

Examples

Ratchet Lifter

Models a ratchet lifter and demonstrates how to use contact proxies for contact problems that involve complex geometries.

• Open Model

Using the Rack-Pinion Block - Windshield Wiper Mechanism

A windshield wiper mechanism. The mechanism utilizes a rack and pinion to drive the wiper blades in a synchronized fashion. The rack is actuated using a scotch yoke coupling (modeled using a pin-slot joint) that converts the rotary motion of the motor to reciprocating motion of the rack. The rack and pinion arrangement converts the reciprocating linear motion of the rack into reciprocating angular motion of the wiper blades (which are rigidly attached to the pinion).

• Open Model

Using the Point-On-Curve Block: Flapping Wing Mechanism

This model simulates a barrel cam based wing flapping mechanism. This is a one degree of freedom mechanism and the two wings flap in sync with each other. The Spline and Point On Curve blocks have been used to model the Barrel Cam mechanism that actuates the flapping motion of the wings.

• Open Model

Ports

Frame

B — Base frame

frame

Base frame of the joint block.

F — Follower frame

frame

Follower frame of the joint block.

Input

X Prismatic Primitive (Px)

fx — Actuation force

physical signal

Physical signal input port that accepts the actuation force for the joint primitive. The block applies the force equally and oppositely to the base and follower frames of the joint along the x-axis of the base frame.

Dependencies

To enable this port, under X Prismatic Primitive (Px) > Actuation, set Force to Provided by Input.

px — Motion profile

physical signal

Physical signal input port that accepts the motion profile for the joint primitive. The block uses this signal to determine the displacement of the follower frame with respect to the base frame along the x-axis of the base frame. The signal must also contain the first and second derivatives of the displacement.

Dependencies

To enable this port, under X Prismatic Primitive (Px) > Actuation, set Motion to Provided by Input.

Z Revolute Primitive (Rz)

tz — Actuation torque

physical signal

Physical signal input port that accepts the actuation torque for the joint primitive. The block applies this torque equally and oppositely to both the base and follower frames of the joint primitive. The torque is about the z-axis of the base frame. The z-axes of the follower and base frames align with each other during simulation.

Dependencies

To enable this port, under Z Revolute Primitive (Rz) > Actuation, set Torque to Provided by Input.

qz — Motion profile

physical signal

Physical signal input port that accepts the motion profile for the joint primitive. The block uses this signal to determine the rotation of the follower frame with respect to the base frame about the z-axis of the base frame. The signal must also contain the first and second derivatives of the rotation.

Dependencies

To enable this port, under Z Revolute Primitive (Rz) > Actuation, set Motion to Provided by Input.

Mode Configuration

mode — Joint mode control

physical signal

Input port that controls the mode of the joint. The signal must be a unitless scalar. The joint mode is normal when the input signal is 0, disengaged when the input signal is -1, and locked when the input signal is 1. You can change the mode at any time during the simulation.

The table shows how the position and velocity of the joint change during transitions between modes.

Transitions	Position	Velocity
Normal to Locked	The joint position retains the current value and remains constant after the transition.	The joint velocity becomes zero and remains constant after the transition.
Normal to Disengaged	The joint position retains the current value but can change in any direction after the transition.	The joint velocity retains the current value but can change in any direction after the transition.
Locked to Normal	The joint position retains the current value but can change in the directions aligned with the joint degrees of freedom (DOFs) after the transition.	The joint velocity remains at zero but can change in the directions aligned with the joint DOFs after the transition.
Locked to Disengaged	The joint position retains the current value but can change in any direction after the transition.	The joint velocity remains at zero but can change in any direction after the transition.
Disengaged to Normal	For the directions aligned with the joint DOFs, the joint positions initially take values calculated by using Newton's method and can change thereafter. In the constrained directions, the joint positions become zero and remain constant after the transition.	For the directions aligned with the joint DOFs, the joint velocities initially take values calculated by using Newton's method and can change thereafter. In the constrained directions, the joint velocities become zero and remain constant after the transition.
Disengaged to Locked	For the directions aligned with the joint DOFs, the joint positions initially take values calculated by using Newton's method and remain constant after the transition. In the constrained directions, the joint positions become zero and remain constant after the transition.	The joint velocity becomes zero and remains constant after the transition.

Dependencies

To enable this port, under Mode Configuration, set Mode to Provided by Input.

Output

X Prismatic Primitive (Px)

px — Position of primitive

physical signal

Physical signal port that outputs the position of the joint primitive. The value is the displacement of the follower frame with respect to the base frame in the x-direction of the base frame.

Dependencies

To enable this port, under X Prismatic Primitive (Px) > Sensing, select Position.

vx — Velocity of primitive

physical signal

Physical signal port that outputs the velocity of the joint primitive. The value is the first derivative of the signal from the port px.

Dependencies

To enable this port, under X Prismatic Primitive (Px) > Sensing, select Velocity.

ax — Acceleration of primitive

physical signal

Physical signal port that outputs the acceleration of the joint primitive. The value is the second derivative of the signal from the port px.

Dependencies

To enable this port, under X Prismatic Primitive (Px) > Sensing, select Acceleration.

fx — Actuator force acting on joint primitive

physical signal

Physical signal port that outputs the actuator force acting on the joint primitive.

Dependencies

To enable this port, under X Prismatic Primitive (Px) > Sensing, select Actuator Force.

fllx — Lower-limit force

physical signal

Physical signal port that outputs the lower-limit force. The block applies this force when the joint primitive position is less than the lower bound of the free region. The block applies this force to both the base and follower frames of the joint primitive in order to accelerate the relative position back to the free region.

Dependencies

To enable this port, under X Prismatic Primitive (Px) > Sensing, select Lower-Limit Force.

fulx — Upper-limit force

physical signal

Physical signal port that outputs the upper-limit force. The block applies this force when the joint primitive position exceeds the upper bound of the free region. The block applies this force to both the base and follower frames of the joint primitive in order to accelerate the relative position back to the free region.

Dependencies

To enable this port, under X Prismatic Primitive (Px) > Sensing, select Upper-Limit Force.

Z Revolute Primitive (Rz)

qz — Position of joint primitive

physical signal

Physical signal port that outputs the position of the joint primitive. The value is the rotation angle of the follower frame with respect to the base frame about the z-axis of the base frame.

Dependencies

To enable this port, under Z Revolute Primitive (Rz) > Sensing, select Position.

wz — Angular velocity of joint primitive

physical signal

Physical signal port that outputs the angular velocity of the joint primitive. The value is the first derivative of the signal from the port qz.

Dependencies

To enable this port, under Z Revolute Primitive (Rz) > Sensing, select Velocity.

bz — Angular acceleration of joint primitive

physical signal

Physical signal port that outputs the angular acceleration of the joint primitive. The value is the second derivative of the signal from the port qz.

Dependencies

To enable this port, under Z Revolute Primitive (Rz) > Sensing, select Acceleration.

tz — Actuator torque acting on joint primitive

physical signal

Physical signal port that outputs the actuator torque acting on the joint primitive.

Dependencies

To enable this port, under Z Revolute Primitive (Rz) > Sensing, select Actuator Torque.

tllz — Lower-limit torque acting on joint primitive

physical signal

Physical signal port that outputs the lower-limit torque. The block applies this torque when the joint primitive position is less than the lower bound of the free region. The block applies this torque to both the base and follower frames of the joint primitive in order to accelerate the relative position back to the free region.

Dependencies

To enable this port, under Z Revolute Primitive (Rz) > Sensing, select Lower-Limit Torque.

tulz — Upper-limit torque acting on joint primitive

physical signal

Physical signal port that outputs the upper-limit torque. The block applies this torque when the joint primitive position exceeds the upper bound of the free region. The block applies this torque to both the base and follower frames of the joint primitive in order to accelerate the relative position back to the free region.

Dependencies

To enable this port, under Z Revolute Primitive (Rz) > Sensing, select Upper-Limit Torque.

Composite Force/Torque Sensing

fc — Constraint force

physical signal

Physical signal port that outputs the constraint forces that act across the joint. The force maintains the translational constraints of the joint. For more information, see Measure Joint Constraint Forces.

Dependencies

To enable this port, under Composite Force/Torque Sensing, select Constraint Force.

tc — Constraint torque

physical signal

Physical signal port that outputs the constraint torques that act across the joint. The torque maintains the rotational constraints of the joint. For more information, see Force and Torque Sensing.

Dependencies

To enable this port, under Composite Force/Torque Sensing, select Constraint Torque.

ft — Total force

physical signal

Physical signal port that outputs the total force that acts across the joint. The total force is the sum of the forces transmitted from one frame to the other through the joint. The force includes the actuation, internal, limit, and constraint forces. See Force and Torque Sensing for more information.

Dependencies

To enable this port, under Composite Force/Torque Sensing, select Total Force.

tt — Total torque

physical signal

Physical signal port that outputs the total torque that acts across the joint. The total torque is the sum of the torques transmitted from one frame to the other through the joint. The torque includes the actuation, internal, limit, and constraint torques. For more information, see Force and Torque Sensing.

Dependencies

To enable this port, under Composite Force/Torque Sensing, select Total Torque.

Parameters

To edit block parameters interactively, use the Property Inspector. From the Simulink^® Toolstrip, on the Simulation tab, in the Prepare gallery, select Property Inspector.

X Prismatic Primitive (Px)

State Targets

Specify Position Target — Whether to specify position target

off (default) | on

Select this parameter to specify the position target for the x prismatic primitive.

Priority — Priority level of position target

High (desired) (default) | Low (approximate)

Priority level of the position target, specified as High (desired) or Low (approximate). For more information, see the Guiding Assembly section of How Multibody Assembly Works.

Dependencies

To enable this parameter, select Specify Position Target.

Value — Position target

0 m (default) | scalar

Position target of the x prismatic primitive, specified as a scalar in units of length.

Dependencies

To enable this parameter, select Specify Position Target.

Specify Velocity Target — Whether to specify linear velocity target

off (default) | on

Select this parameter to specify the linear velocity target for the x prismatic primitive.

Priority — Priority level of linear velocity target

High (desired) (default) | Low (approximate)

Priority level of the linear velocity target, specified as High (desired) or Low (approximate). For more information, see the Guiding Assembly section of How Multibody Assembly Works.

Dependencies

To enable this parameter, select Specify Velocity Target.

Value — Velocity target

0 m/s (default) | scalar

Linear velocity target for the x prismatic primitive, specified as a scalar in units of linear velocity.

Dependencies

To enable this parameter, select Specify Velocity Target.

Internal Mechanics

Equilibrium Position — Position where internal force is zero

0 m (default) | scalar

Position where the spring force is zero, specified as a scalar in units of length.

Spring Stiffness — Stiffness of force law

0 N/m (default) | scalar

Stiffness of the internal spring-damper force law for the joint primitive, specified as a scalar in units of linear stiffness.

Damping Coefficient — Damping coefficient of force law

0 N(m/s) (default) | scalar

Damping coefficient of the internal spring-damper force law for the joint primitive, specified as a scalar in units of linear damping coefficient.

Limits

Specify Lower Limit — Whether to specify lower position limit

off (default) | on

Select this parameter to specify the lower limit of the x prismatic primitive.

Bound — Lower bound of free region

-1 m (default) | scalar

Lower bound of the free region of the x prismatic primitive, specified as a scalar in units of length.

Dependencies

To enable this parameter, select Specify Lower Limit.

Spring Stiffness — Stiffness of spring at lower bound

1e6 N/m (default) | scalar

Stiffness of the spring at the lower bound, specified as a scalar in units of linear stiffness.

Dependencies

To enable this parameter, select Specify Lower Limit.

Damping Coefficient — Damping coefficient at lower bound

1e3 N/(m/s) (default) | scalar

Damping coefficient at the lower bound, specified as a scalar in units of linear damping coefficient.

Dependencies

To enable this parameter, select Specify Lower Limit.

Transition Region Width — Region to smooth spring and damper forces

1e-4 m (default) | scalar

Region to smooth the spring and damper forces, specified as a scalar in units of length.

The block applies the full value of the lower-limit force when the penetration reaches the width of the transition region. The smaller the region, the sharper the onset of forces and the smaller the time step required of the solver. In the tradeoff between simulation accuracy and simulation speed, reducing the transition region improves accuracy and expanding it improves speed.

Dependencies

To enable this parameter, select Specify Lower Limit.

Specify Upper Limit — Whether to specify upper position limit

off (default) | on

Select this parameter to specify the upper limit of the x prismatic primitive.

Bound — Upper bound of free region

1 m (default) | scalar

Upper bound for the free region of the joint primitive, specified as a scalar in units of length.

Dependencies

To enable this parameter, select Specify Upper Limit.

Spring Stiffness — Stiffness of spring at upper bound

1e6 N/m (default) | scalar

Stiffness of the spring at the upper bound, specified as a scalar in units of linear stiffness.

Dependencies

To enable this parameter, select Specify Upper Limit.

Damping Coefficient — Damping coefficient at upper bound

1e3 N/(m/s) (default) | scalar

Damping coefficient at the upper bound, specified as a scalar in units of linear damping coefficient.

Dependencies

To enable this parameter, select Specify Upper Limit.

Transition Region Width — Region to smooth spring and damper forces

1e-4 m (default) | scalar

Region to smooth the spring and damper forces, specified as a scalar in units of length.

The block applies the full value of the upper-limit force when the penetration reaches the width of the transition region. The smaller the region, the sharper the onset of forces and the smaller the time step required of the solver. In the tradeoff between simulation accuracy and simulation speed, reducing the transition region improves accuracy and expanding it improves speed.

Dependencies

To enable this parameter, select Specify Upper Limit.

Actuation

Force — Option to provide actuator force

None (default) | Provided by Input | Automatically Computed

Option to provide the actuator force for the joint primitive, specified as one of these values:

Force Setting	Description
None	No actuator force.
Provided by Input	The input port fx specifies the actuator force for the x prismatic primitive.
Automatically Computed	The block automatically calculates the amount of force required to satisfy the motion inputs to the mechanism. If you set this parameter to Automatically Computed, you do not need to set Motion to Provided by Input for the same joint primitive. The automatically computed force may satisfy a motion input elsewhere in the mechanism.

Motion — Option to provide motion

Automatically Computed (default) | Provided by Input

Option to provide the motion for the joint primitive, specified as one of these values:

Motion Setting	Description
Automatically Computed	The block computes and applies the joint primitive motion based on the model dynamics.
Provided by Input	The input port px specifies the motion for the joint primitive.

Z Revolute Primitive (Rz)

State Targets

Specify Position Target — Whether to specify position target

off (default) | on

Select this parameter to specify the position target of the z revolute primitive.

Priority — Priority level of position target

High (desired) (default) | Low (approximate)

Priority level of the position target, specified as High (desired) or Low (approximate). For more information, see the Guiding Assembly section of How Multibody Assembly Works.

Dependencies

To enable this parameter, select Specify Position Target.

Value — Position target

0 deg (default) | scalar

Position target of the z revolute primitive, specified as a scalar with a unit of angle.

Dependencies

To enable this parameter, select Specify Position Target.

Specify Velocity Target — Whether to specify angular velocity target

off (default) | on

Select this parameter to specify the angular velocity target for the z revolute primitive.

Priority — Priority level of velocity target

High (desired) (default) | Low (approximate)

Priority level of the angular velocity target, specified as High (desired) or Low (approximate). For more information, see the Guiding Assembly section of How Multibody Assembly Works.

Dependencies

To enable this parameter, select Specify Velocity Target.

Value — Velocity target

0 deg/s (default) | scalar

Angular velocity target of the z revolute primitive, specified as a scalar with a unit of angular velocity.

Dependencies

To enable this parameter, select Specify Velocity Target.

Internal Mechanics

Equilibrium Position — Position where internal torque is zero

0 deg (default) | scalar

Position where the spring torque is zero, specified as a scalar with a unit of angle.

Spring Stiffness — Stiffness of force law

0 N*m/deg (default) | scalar

Stiffness of the internal spring-damper force law for the z revolute primitive, specified as a scalar with a unit of torsional stiffness.

Damping Coefficient — Damping coefficient of force law

0 N*m/(deg/s) (default) | scalar

Damping coefficient of the internal spring-damper force law for the z revolute primitive, specified as a scalar with a unit of damping coefficient.

Limits

Specify Lower Limit — Whether to specify lower position limit

off (default) | on

Select this parameter to specify the lower limit of the z revolute primitive.

Bound — Lower bound of free region

-90 deg (default) | scalar

Lower bound for the free region of the z revolute primitive, specified as a scalar with a unit of angle.

Dependencies

To enable this parameter, select Specify Lower Limit.

Spring Stiffness — Stiffness of spring at lower bound

1e4 N*m/deg (default) | scalar

Stiffness of the spring at the lower bound, specified as a scalar with a unit of torsional stiffness.

Dependencies

To enable this parameter, select Specify Lower Limit.

Damping Coefficient — Damping coefficient at lower bound

10 N*m/(deg/s) (default) | scalar

Damping coefficient at the lower bound, specified as a scalar with a unit of damping coefficient.

Dependencies

To enable this parameter, select Specify Lower Limit.

Transition Region Width — Region to smooth spring and damper torques

0.1 deg (default) | scalar

Region to smooth the spring and damper torques, specified as a scalar with a unit of angle.

The block applies the full value of the lower-limit torque when the penetration reaches the width of the transition region. The smaller the region, the sharper the onset of forces and the smaller the time step required of the solver. In the tradeoff between simulation accuracy and simulation speed, reducing the transition region improves accuracy and expanding it improves speed.

Dependencies

To enable this parameter, select Specify Lower Limit.

Specify Upper Limit — Whether to specify upper position limit

off (default) | on

Select this parameter to specify the upper limit of the z revolute primitive.

Bound — Upper bound of free region

90 deg (default) | scalar

Upper bound for the free region of the z revolute primitive, specified as a scalar with a unit of angle.

Dependencies

To enable this parameter, select Specify Upper Limit.

Spring Stiffness — Stiffness of spring at upper bound

1e4 N*m/deg (default) | scalar

Stiffness of the spring at the upper bound, specified as a scalar with a unit of torsional stiffness.

Dependencies

To enable this parameter, select Specify Upper Limit.

Damping Coefficient — Damping coefficient at upper bound

10 N*m/(deg/s) (default) | scalar

Damping coefficient at the upper bound, specified as a scalar with a unit of damping coefficient.

Dependencies

To enable this parameter, select Specify Upper Limit.

Transition Region Width — Region to smooth spring and damper torques

0.1 deg (default) | scalar

Region to smooth the spring and damper torques, specified as a scalar with a unit of angle.

The block applies the full value of the upper-limit torque when the penetration reaches the width of the transition region. The smaller the region, the sharper the onset of forces and the smaller the time step required of the solver. In the tradeoff between simulation accuracy and simulation speed, reducing the transition region improves accuracy and expanding it improves speed.

Dependencies

To enable this parameter, select Specify Upper Limit.

Actuation

Torque — Option to provide actuator torque

None (default) | Provided by Input | Automatically Computed

Option to provide the actuator torque for the joint primitive, specified as one of these values:

Torque Setting	Description
None	No actuator torque.
Provided by Input	The input port tz specifies the actuator torque for the z revolute primitive.
Automatically Computed	The block computes the torque automatically. If you set this parameter to Automatically Computed, you do not need to set Motion to Provided by Input for the for the same joint primitive. The automatically computed torque may satisfy a motion input somewhere else in the mechanism.

Motion — Option to provide motion

Automatically Computed (default) | Provided by Input

Option to provide the motion for the joint primitive, specified as one of these values:

Motion Setting	Description
Automatically computed	The block computes and applies the joint primitive motion based on model dynamics.
Provided by Input	The input port qz specifies the motion for the z revolute primitive.

Mode Configuration

Mode — Joint mode

Normal (default) | Locked | Disengaged | Provided by Input

Joint mode for the simulation, specified as one of these values:

Mode	Description
Locked	Locked mode constrains all the degrees of freedom (DOFs) for the joint. The locked joint maintains its initial assembly position with zero velocity during the simulation. The joint block can sense forces or torques in accordance with the settings of the Internal Mechanics, Limits, and Actuation parameters.
Normal	Normal mode enables the DOFs and the constraints of the joint work as intended during the simulation.
Disengaged	Disengaged mode releases the joint from all constraints throughout the simulation. The settings for Internal Mechanics, Limits, and Actuation parameters do not affect the disengaged joint. All output ports output zero.
Provided by Input	The Provided by Input option allows you to specify the joint mode by using an input signal. For more information, see the port mode in the Input section.

Composite Force/Torque Sensing

Direction — Measurement direction

Follower on Base (default) | Base on Follower

Measurement direction, specified as one of these values:

• Follower on Base — The block senses the force and torque that the follower frame exerts on the base frame.

• Base on Follower — The block senses the force and torque that the base frame exerts on the follower frame.

This parameter affects only the output signals under the Composite Force/Torque Sensing section. Reversing the direction changes the sign of the measurements. For more information, see Force and Torque Measurement Direction.

Resolution Frame — Frame used to resolve measurements

Base (default) | Follower

Frame used to resolve the measurements, specified as one of these values:

• Base — The block resolves the measurements in the coordinates of the base frame.

• Follower — The block resolves the measurements in the coordinates of the follower frame.

This parameter affects only the output signals under the Composite Force/Torque Sensing section.

Extended Capabilities

C/C++ Code Generation
Generate C and C++ code using Simulink® Coder™.

Version History

Introduced in R2013a