Polar Plot Axis is Off Center from and not Scaled with Background Image
4 visualizaciones (últimos 30 días)
Mostrar comentarios más antiguos
I am trying to plot acceptable values of saturation on an HSV Color Wheel, but the polar plot is not centered on the background image. Anyone have any good ways to get the radius right and improve the plot to be centered on the background?
minS = 15;
maxS = 30;
minH = 50; %because yellow is apparently yucky
c = (-1*minS+maxS)/2;
a = maxS-c;
ellipticity = c/a;
parameter = a*(1-ellipticity^2);
theta = 0:0.1:360;
rho = parameter./(1-ellipticity.*cosd(theta - minH + 180));
rows = 500;
columns = 500;
midX = columns / 2;
midY = rows / 2;
% Construct v image as uniform.
v = ones(rows, columns);
s = zeros(size(v)); % Initialize.
h = zeros(size(v)); % Initialize.
% Construct the h image as going from 0 to 1 as the angle goes from 0 to 360.
% Construct the S image going from 0 at the center to 1 at the edge.
for c = 1 : columns
for r = 1 : rows
% Radius goes from 0 to 1 at edge, a little more in the corners.
radius = sqrt((r - midY)^2 + (c - midX)^2) / min([midX, midY]);
s(r, c) = min(1, radius); % Max out at 1
h(r, c) = atan2d((r - midY), (c - midX));
end
end
% Flip h right to left.
h = fliplr(mat2gray(h));
% Construct the hsv image.
hsv = cat(3, h, s, v);
rgbImage = hsv2rgb(hsv);
% Display the RGB image.
fig = figure;
subplot(1,1,1);
imshow(rgbImage, []);
drawnow;
polaraxes("Color","none");
hold on;
theta_radians = deg2rad(theta);
polarplot(theta_radians,rho,'black');
rlim([0, 100]);
0 comentarios
Respuestas (1)
yanqi liu
el 23 de Mzo. de 2022
minS = 15;
maxS = 30;
minH = 50; %because yellow is apparently yucky
c = (-1*minS+maxS)/2;
a = maxS-c;
ellipticity = c/a;
parameter = a*(1-ellipticity^2);
theta = 0:0.1:360;
rho = parameter./(1-ellipticity.*cosd(theta - minH + 180));
rows = 500;
columns = 500;
midX = columns / 2;
midY = rows / 2;
% Construct v image as uniform.
v = ones(rows, columns);
s = zeros(size(v)); % Initialize.
h = zeros(size(v)); % Initialize.
% Construct the h image as going from 0 to 1 as the angle goes from 0 to 360.
% Construct the S image going from 0 at the center to 1 at the edge.
for c = 1 : columns
for r = 1 : rows
% Radius goes from 0 to 1 at edge, a little more in the corners.
radius = sqrt((r - midY)^2 + (c - midX)^2) / min([midX, midY]);
s(r, c) = min(1, radius); % Max out at 1
h(r, c) = atan2d((r - midY), (c - midX));
end
end
% Flip h right to left.
h = fliplr(mat2gray(h));
% Construct the hsv image.
hsv = cat(3, h, s, v);
rgbImage = hsv2rgb(hsv);
% Display the RGB image.
fig = figure;set(gca, 'units','normalized','position',[0,0,1,1])
imshow(rgbImage, []);
drawnow;
polaraxes("Color","none");
hold on;
theta_radians = deg2rad(theta);
hp2 = polarplot(theta_radians,rho,'black');
rlim([0, 100]);
0 comentarios
Ver también
Categorías
Más información sobre Introduction to Installation and Licensing en Help Center y File Exchange.
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!