Increasing the caclulation speed while using loops

1 visualización (últimos 30 días)
Hamid
Hamid el 17 de Nov. de 2022
Editada: Stephen23 el 18 de Nov. de 2022
Dear MATLAB experts,
I considered a range for x and y and if x1 and y1 are within a specific range the code must convert x1 and y1 to the mean value of the specific range.
In other words, considering a pixel and if the values of x and y are inside the pixel, I wanted to replace the values with the position of the center of the pixel as shown in the attached file (if x and y are black corss must be replaced with red one)
Code is working but as the data is very big, the calculation speed is slow. Is there any modifications that may lead to increase the speed of calculations?
Thank you in advance.
data = load('data.mat').out1_com;
det_x = 50;
det_y = 50;
det_ch = 16;
%%
xedges = -(det_x/2):(det_x/det_ch):(det_x/2);
yedges = -(det_y/2):(det_y/det_ch):(det_y/2);
kf = data(:,1);
x1 = data(:,2);
y1 = data(:,3);
z1 = data(:,4);
len = length(x1);
x11 = zeros(len,1);
y11 = zeros(len,1);
for k=1:length(x1)
for i = 1:length(xedges)-1
for j = 1:length(yedges)-1
idx1 = (xedges(i) <= x1(k)) & ((x1(k)) < xedges(i+1)) & (yedges(j) <= (y1(k))) & ((y1(k)) < yedges(j+1));
if (idx1 == 1)
x11(k)=(xedges(i)+xedges(i+1)) ./ 2;
y11(k)=(yedges(j)+yedges(j+1)) ./ 2;
end
end
end
end
pos=[kf,x11,y11,z1];
  3 comentarios
Hamid
Hamid el 18 de Nov. de 2022
@Stephen23 Thank you so much for your comment. The problem is I don't want to count the points in each pixel and want to replace the values with mean value of edges.
Stephen23
Stephen23 el 18 de Nov. de 2022
Editada: Stephen23 el 18 de Nov. de 2022
"The problem is I don't want to count the points in each pixel "
You would use the 4th and 5th outputs (bin indices), not the 1st and 2nd outputs (counts).

Iniciar sesión para comentar.

Respuesta aceptada

David Goodmanson
David Goodmanson el 17 de Nov. de 2022
Editada: David Goodmanson el 17 de Nov. de 2022
Hi Hamid,
Hi Hamid, I have not speed checked this but it should be faster (the range in your example is different from the drawing).
det_x = 50;
det_y = 50;
det_ch = 16;
%
xedges = -(det_x/2):(det_x/det_ch):(det_x/2)
yedges = -(det_y/2):(det_y/det_ch):(det_y/2);
xmid = (xedges(1:end-1)+xedges(2:end))/2;
ymid = (yedges(1:end-1)+yedges(2:end))/2;
x = -25+50*rand(1,2000); % some data in -25< x,y <25
y = -25+50*rand(1,2000);
xr = round((x+25)*16/50 +1/2);
yr = round((y+25)*16/50 +1/2);
xnew = (xr-1/2)*50/16-25;
ynew = (yr-1/2)*50/16-25;
plot(x,y,'.',xnew,ynew,'o')
  3 comentarios
David Goodmanson
David Goodmanson el 18 de Nov. de 2022
Hi Hamid,
I guess you are really asking only about xmid and ymid, since you defined xedges and yedges. I was going to use xmid, ymid to verify that the xnew and ynew arrays were ending up with the right values, but I realized that xnew and ynew were doing the right thing so I never used the check.
Hamid
Hamid el 18 de Nov. de 2022
Hi David,
I see. Thanks a lot!

Iniciar sesión para comentar.

Más respuestas (0)

Categorías

Más información sobre Matrix Indexing en Help Center y File Exchange.

Productos


Versión

R2022b

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by