What is the difference between "phased.LinearFMWaveform" and "phased.FMCWWaveform"
4 visualizaciones (últimos 30 días)
Mostrar comentarios más antiguos
AR
el 27 de Dic. de 2012
Editada: PATRICK UWIGIZE
el 30 de Dic. de 2021
1. What is the difference between "phased.LinearFMWaveform" and "phased.FMCWWaveform" in Phased Array System Toolbox except for that Triangle waveform generation is possible in P"phased.LinearFMWaveform" function.
2. My other concern is I want to sweep bandwidth of 10Mhz from start frequency of 10 MHz and End Frequency 20MHz. How can i do that in "phased.LinearFMWaveform" function.
3. When i dechirp the received signal from transmitted signal of saw-tooth waveform, i should get 2 beat frequencies (according to "New ideas in FM Radar by H. D. Griffiths"). but i get only 1 beat frequency, why?
0 comentarios
Respuesta aceptada
Honglei Chen
el 27 de Dic. de 2012
Hi Ali,
LinearFMWaveform is a pulse waveform, meaning that in general the system only transmit a very short period of time during one cycle and uses the rest of cycle to receive. On the other hand, FMCWWaveform is a continuous waveform, so the system transmits and receives at the same time and the duty cycle for the waveform is always 1.
Currently you cannot specify the starting and ending frequencies in LinearFMWaveform. However, depending on the system setup, you may still be able to simulate your case. For example, if your system's center frequency is 15 MHz, then your situation is just a symmetric sweeping over a 10MHz range.
I don't have that particular paper handy so I cannot comment much on your third question without seeing some code snippet.
HTH
4 comentarios
Más respuestas (1)
Nadir HEFHAF
el 10 de Sept. de 2017
Editada: Honglei Chen
el 11 de Sept. de 2017
i have problem also in this program
close all
clc
clear all
L = 50;
N = 4;
rxULA = phased.ULA('Element',phased.OmnidirectionalMicrophoneElement,...
'NumElements',N);
rxpos1 = [0;0;0];
rxvel1 = [0;0;0];
rxax1 = azelaxes(90,0);
rxpos2 = [L;0;0];
rxvel2 = [0;0;0];
rxax2 = rxax1;
srcpos = [30;100;0];
srcvel = [0;0;0];
srcax = azelaxes(-90,0);
srcULA = phased.OmnidirectionalMicrophoneElement;
fc = 300e3; % 300 kHz
c = 1500; % 1500 m/s
dmax = 150; % 150 m
pri = (2*dmax)/c;
prf = 1/pri;
bw = 100.0e3; % 100 kHz
fs = 2*bw;
waveform = phased.LinearFMWaveform('SampleRate',fs,'SweepBandwidth',bw,...
'PRF',prf,'PulseWidth',pri/10);
signal = waveform();
nfft = 128;
radiator = phased.WidebandRadiator('Sensor',srcULA,...
'PropagationSpeed',c,'SampleRate',fs,...
'CarrierFrequency',fc,'NumSubbands',nfft);
collector1 = phased.WidebandCollector('Sensor',rxULA,...
'PropagationSpeed',c,'SampleRate',fs,...
'CarrierFrequency',fc,'NumSubbands',nfft);
collector2 = phased.WidebandCollector('Sensor',rxULA,...
'PropagationSpeed',c,'SampleRate',fs,...
'CarrierFrequency',fc,'NumSubbands',nfft);
channel1 = phased.WidebandFreeSpace('PropagationSpeed',c,...
'SampleRate',fs,'OperatingFrequency',fc,'NumSubbands',nfft);
channel2 = phased.WidebandFreeSpace('PropagationSpeed',c,...
'SampleRate',fs,'OperatingFrequency',fc,'NumSubbands',nfft);
[~,ang1t] = rangeangle(rxpos1,srcpos,srcax);
[~,ang2t] = rangeangle(rxpos2,srcpos,srcax);
sigt = radiator(signal,[ang1t ang2t]);
sigp1 = channel1(sigt(:,1),srcpos,rxpos1,srcvel,rxvel1);
sigp2 = channel2(sigt(:,2),srcpos,rxpos2,srcvel,rxvel2);
[~,ang1r] = rangeangle(srcpos,rxpos1,rxax1);
[~,ang2r] = rangeangle(srcpos,rxpos2,rxax2);
sigr1 = collector1(sigp1,ang1r);
sigr2 = collector2(sigp2,ang2r);
doa1 = phased.GCCEstimator('SensorArray',rxULA,'SampleRate',fs,...
'PropagationSpeed',c);
doa2 = phased.GCCEstimator('SensorArray',rxULA,'SampleRate',fs,...
'PropagationSpeed',c);
angest1 = doa1(sigr1);
angest2 = doa2(sigr2);
yest = L/(abs(tand(angest1)) + abs(tand(angest2)));
xest = yest*abs(tand(angest1));
zest = 0;
srcpos_est = [xest;yest;zest]
the problem is
Array formation and parentheses-style indexing with objects of class 'phased.LinearFMWaveform' is not allowed. Use objects of class 'phased.LinearFMWaveform' only as scalars or use a cell array.
Error in program11 (line 27) signal = waveform();
3 comentarios
Harwanto Zidqi Putro
el 12 de Ag. de 2020
Editada: Harwanto Zidqi Putro
el 12 de Ag. de 2020
I have version 2016a, and its error with same problem
PATRICK UWIGIZE
el 30 de Dic. de 2021
Editada: PATRICK UWIGIZE
el 30 de Dic. de 2021
Upgrade you MATLAB to a newer version
Ver también
Categorías
Radar
Phased Array System Toolbox
Phased Array Design and Analysis
Antennas, Microphones, and Sonar Transducers
Mostrar más
Más información sobre Linear Prediction en Help Center y File Exchange.
Productos
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!