Resuelto
Back and Forth Rows
Given a number n, create an n-by-n matrix in which the integers from 1 to n^2 wind back and forth along the rows as shown in the...
alrededor de 10 años hace
Resuelto
Sum all integers from 1 to 2^n
Given the number x, y must be the summation of all integers from 1 to 2^x. For instance if x=2 then y must be 1+2+3+4=10.
alrededor de 10 años hace
Resuelto
Finding Perfect Squares
Given a vector of numbers, return true if one of the numbers is a square of one of the other numbers. Otherwise return false. E...
alrededor de 10 años hace
Resuelto
find the Area of a rectangle
length is x width is y what is the area of the rectangle?
alrededor de 10 años hace
Resuelto
Times 2 - START HERE
Try out this test problem first. Given the variable x as your input, multiply it by two and put the result in y. Examples:...
alrededor de 10 años hace
Enviada
Using MATLAB for Bearing Fault Analysis
Ball Bearings can have several faults, which result in different signals. This program shows this.
más de 10 años hace | 6192 descargas |
Enviada
Pause a long MATLAB run with a simple click.
A simple way to pause a long simulation, to check progress, without expensive breakpoints or checks
más de 10 años hace | 3128 descargas |
Resuelto
Compute the step response of a DC motor
Compute the step response of a DC motor shown below <<http://blogs.mathworks.com/images/seth/cody/dc-motor.png>> The param...
alrededor de 11 años hace
Resuelto
Model a simple pendulum
Model a simple pendulum of length 200cm with bob of mass 100g and plot the position in degrees. The pendulum starts at 30 degree...
alrededor de 11 años hace
Resuelto
Produce a Fibonacci sequence
Construct a diagram that generates the Fibonacci sequence: 1, 1, 2, 3, 5, 8, 13, 21, 34.....up to 377 The Fibonacci sequ...
alrededor de 11 años hace
Resuelto
Make a low pass filter
Make a first order low pass filter that will filter out the high frequency oscillations for the given input signal. The cut-off ...
alrededor de 11 años hace
Resuelto
Model a falling body
An object is falling freely from a height of 22 meters under the force of gravity. <<http://blogs.mathworks.com/images/seth/c...
alrededor de 11 años hace
Resuelto
Model a mass spring system
Model an ideal mass-spring system shown below where the spring is initially stretched. <<http://blogs.mathworks.com/images/se...
alrededor de 11 años hace
Resuelto
Counting pulses in a signal
Count the number of pulses that are the result of summing each pulse generator block. Pulse Generator blocks produce a recurr...
alrededor de 11 años hace
Resuelto
Add damping to a mass spring system
Model an ideal mass-spring-damper system shown below where the spring is initially stretched. <<http://blogs.mathworks.com/im...
alrededor de 11 años hace
Resuelto
Make a full wave rectifier
Produce a full wave rectifier waveform for the given sine wave source. For a sine wave input, the output of the full wave rec...
alrededor de 11 años hace
Resuelto
Make a half wave rectifier
Produce a signal that outputs the given sine wave source when it is greater than zero and outputs zero when it is less than zero...
alrededor de 11 años hace
Resuelto
Produce a sine wave
Produce a sine wave with amplitude 3: <<http://blogs.mathworks.com/images/seth/cody/sine-eqn.png>>
alrededor de 11 años hace
Resuelto
Add a block to a model
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-block-eqn.png>> In this case, the slope of...
alrededor de 11 años hace
Resuelto
Add offset to a signal
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-offset-eqn.png>> You should see a downward...
alrededor de 11 años hace
Resuelto
Produce a cosine wave
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/cosine-eqn.png>>
alrededor de 11 años hace
Resuelto
Connect blocks in a model
Connect the blocks in the model to produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/connect-blocks...
alrededor de 11 años hace
Enviada
Designing a controller for an Inverted Pendulum - hebrew
Designing a controller for an Inverted Pendulum - hebrew
más de 12 años hace | 715 descargas |
Enviada
Using Simscape for design of Multi-Domain Physical Systems
Using Simscape for design of Multi-Domain Physical Systems
más de 12 años hace | 512 descargas |
Enviada
Using SimMechanics for designing and testing Mechanical Systems
A Presentation and demos for using Simulink, SolidWorks and SimMechanics.
más de 12 años hace | 812 descargas |
Enviada
Using Model-Predicite Control - Presentation and Recording - Hebrew
Using Model-Predictive Control (MPC) for Control Design
más de 12 años hace | 716 descargas |
Enviada
Converting Dataset Simulation results to Excel Spreadsheet
Two simple functions that convert a Dataset parameter, containing Simulink Simulation data, to excel
más de 13 años hace | 1295 descargas |
Enviada
Comparing different methods to solve an Inverted Pendulum problem
A simple reporting tool that shows how you can model an inverted pendulum in a few methods.
más de 13 años hace | 2212 descargas |
Enviada
Reporting tools in the MATLAB and Simulink Environment
This submission shows how you can export your results from MATLAB, via different reports.
más de 13 años hace | 606 descargas |
Enviada
Reporting tools in the MATLAB and Simulink Environment
Three ways to report your results to someone who doesn't use MATLAB.
más de 13 años hace | 572 descargas |
