photo

Neil MacEwen

MathWorks

Last seen: 2 días hace Con actividad desde 2015

Followers: 1   Following: 0

Principal Engineer - wireless and software defined radio.

Estadística

  • Knowledgeable Level 3
  • First Review
  • 6 Month Streak
  • Revival Level 2
  • Knowledgeable Level 2
  • First Answer

Ver insignias

Feeds

Ver por

Respondida
Can Matlab calibrate USRP N310 SDR? + Filtering noise
Hi J, Please have a look at this example - https://www.mathworks.com/help/comm/usrpradio/ug/direction-of-arrival-estimation-usi...

12 días hace | 1

| aceptada

Respondida
USRP X310 HDL coder
As of R2024a, the USRP X310 is supported for code generation workflows in Wireless Testbench.

5 meses hace | 0

Respondida
Does Matlab support system objects for X410 USRP?
Hi, Comm.SDRuTransmitter and comm.SDRuReceiver are not supported for the X410 at the moment, but it is under consideration for...

5 meses hace | 0

| aceptada

Respondida
how to connect two USRP x310 to a computer?
By default, all X310s will have the same IP address, so one must be changed to use them together. Using setsdruip to change the ...

9 meses hace | 0

Respondida
Quesiton about transmitRepeat(sdrTransmit, data) and sdrTransmit.Repeat(txWavefrom)
Hi, I'm afraid transmitRepeat is not a supported functionality for the USRP B210. All transmission for that hardware uses stream...

más de 2 años hace | 0

Respondida
mwip kernel module on Zynq 7000 series and AD 9361
Hi Ratin, mwipcore doesn't interact with the AD9361 at all, it is used to configure the user IPCore that has been built into th...

más de 2 años hace | 0

Respondida
FMCOMMS2/3/4 MIMO Simulink Example
Hi Fayez, I'm afraid the example that you have found is the only example that uses more than one antenna. It would be expected ...

alrededor de 3 años hace | 0

Respondida
zynq linux showing no display
Hi, The image supported by the Xilinx Zynq-Based Radio hardware support package has no support for a display, it can only be co...

alrededor de 3 años hace | 0

Respondida
How to make FMCOMMS2/3/4 and zedboard's SDR firmware from scratch?
Hi, This answer provides an overview on support for a custom board. In addition, here is the information about the source for o...

alrededor de 3 años hace | 0

| aceptada

Respondida
Issues with ADI MATLAB Transceiver Toolbox and Zynq Radio Support Package
Hi, please can you direct questions about ADI's Transceiver Toolbox to ADI's Engineer Zone, specifically the Software Interface ...

más de 3 años hace | 0

Respondida
how to create a cfg file to ad9361 ?
Hi Raz, As you are using ADI's Simulink block and code, the best place to get answers is on their Engineer Zone. MathWorks prov...

casi 4 años hace | 0

Respondida
How to Enhance AD9361 Transmission Power using Support Package for Xilinx Zynq-Based Radio
Hi Ivan, The MathWorks support package operates through ADI drivers, and this being a hardware question, it would be better dir...

casi 4 años hace | 0

| aceptada

Respondida
Quesiton about transmitRepeat(sdrTransmit, data) and sdrTransmit.Repeat(txWavefrom)
Hi Jarul, The interface has not changed, it is still transmitRepeat. In the 802.11a example, the data to be sent is split into ...

más de 4 años hace | 0

Respondida
Can I receive real LTE data with zynq board & RF board?
Hi, yes you should be able to do this with your FMCOMMS5. You can either look at the code used in the transmit and receive func...

casi 5 años hace | 0

| aceptada

Respondida
Install Communication ToolBox Support Package for Xilinx zynq Based Radio on MATLAB 2019b
There was a short term outage of some of the required third party downloads which should now be resolved.

alrededor de 5 años hace | 0

Respondida
HW/SW Codesign QPSK Transmitter and and Receiver Example runing problems
Hi Yang, The ADS-B model has been designed to work with bursty signals. The QPSK model has been designed to work with streaming...

alrededor de 5 años hace | 0

Respondida
Zynq Radio QPSK receiver example errors with "block_diagram does not have a parameter named 'HDLCodeGenStatus'
You may see this error if you do not have HDL Coder installed. In brief, some HDL Coder configuration information was mistakenly...

alrededor de 5 años hace | 0

| aceptada

Pregunta


Zynq Radio QPSK receiver example errors with "block_diagram does not have a parameter named 'HDLCodeGenStatus'
In the Communications Toolbox Hardware Support Package for Xilinx Zynq-Based Radio, when running the QPSK Receiver Simulink mode...

alrededor de 5 años hace | 1 respuesta | 0

1

respuesta

Respondida
ZCU102 hardware setup fails
Hi Matthias, Kambiz, We have updated the bootloader to be compatible with the new DDR, you can find it here. We have only perfo...

alrededor de 5 años hace | 1

Respondida
AD9361 Transceiver Help with FastLock Profile
Hi William, I'm afraid it's not possible to use the fastlock functionality in the current E310 system objects, and you are corr...

más de 5 años hace | 1

| aceptada

Respondida
HW/SW Codesign QPSK Transmitter and and Receiver Example runing problems
Hi Yang, This example has been designed as a streaming system, and the receiver has not been designed to cope with interruption...

más de 5 años hace | 1

| aceptada

Respondida
Dropped samples error in Over the air LTE transmission
Hi Mughda, Underflows are not surprising when trying to stream data in real-time from MATLAB/Simulink to the SDR hardware. Eith...

casi 6 años hace | 0

Respondida
hdl coder zynq support package direct link for the zip file
Hi Shalu, Please contact Technical Support for this question. Kind regards, Neil

casi 6 años hace | 0

Respondida
How can I migrate MathWorks support on ZedBoard to Xilinx ZC702 board?
Hi Lucky, It depends on what you are trying to do. They are the same chip but unfortunately the steps required to enable our fu...

casi 6 años hace | 0

| aceptada

Respondida
Programing Zynq device in ADALM-PLUTO using Simulink
Hi Alejandro, Unfortunately there is no capability to program either the ARM processor or the FPGA fabric from our tools. The...

alrededor de 6 años hace | 0

| aceptada

Respondida
How does a retargeted model know about the subsystem on the FPGA?
Hi Harry, I am going to assume that you are using the <https://www.mathworks.com/help/supportpkg/xilinxzynqbasedradio/ug/fpga...

alrededor de 6 años hace | 1

| aceptada

Respondida
Zynq SDR Receiver Block outputs data regardless of hardware state/cannot detect 802.11 beacons.
Hi Harry, This example will only receive 802.11b standard waveforms. I believe many routers do not transmit that beacon by de...

alrededor de 6 años hace | 2

| aceptada

Respondida
HW/SW Co-design QPSK Transceiver example - Will only load Tx channel onto ADRV9361?
Hi Harry, You have hit a bug in our information returned here I'm afraid. If you target both transmitter and receiver, it wil...

alrededor de 6 años hace | 1

| aceptada

Respondida
How can I enable my E310 to receive over-the-air ADS-B Signals?
Hi Ben, To disable the transmitter, right click on the transmitter block and select "Comment Out". Do the same for the consta...

más de 6 años hace | 0

Respondida
Communications System Toolbox Support for Xilinx Zynq-based SDR - is the Xilinx ZC702 board supported?
Hi Kevin, Unfortunately the ZC702 is not on our list of supported devices. The ZC706 and ZedBoard both have different hardwar...

más de 6 años hace | 0

Cargar más