UDP Receive

Receive data over UDP network from a remote device

Since R2020b

• 

Libraries:
Simulink Real-Time / IP

Description

The UDP Receive block receives data over a UDP network from a remote device. It can receive data by using the connection between the MATLAB^® development computer and Speedgoat^® target computers or by using a dedicated Ethernet card. If you use a dedicated Ethernet card, use the Speedgoat configuration utility to configure the dedicated Ethernet board.

The parameter Local IP address applies when the block executes in a real-time application on a target computer or in a model simulation on a development computer. If your model is running in Simulink^® on the development computer, you can use this block to receive data to a remote device. In this case, the Windows^® operating system determines the network connection.

Examples

Target to Host Transmission by Using UDP

Use UDP blocks to send data from a target computer to a development computer.

• Open Model

Apply UDP Receive Block with Messages from Multiple IP Senders

Use UDP Receive blocks to receive messages from multiple IP addresses.

• Open Script

Ports

Output

Data — Data received

vector

Vector of uint8 containing data received over the UDP network. If no new packet is received, the data values are held. To determine whether a new packet has been received, use the Length output port. If you enable the Enable Simulink messages parameter, the data type is UDP_Packet. This data type consists of:

• IP_Address: DataType: uint8, Complexity: real, Dimensions: [4 1]

• IP_Port: DataType: uint16, Complexity: real, Dimensions: 1

• Length: DataType: uint16, Complexity: real, Dimensions: 1

• Data: DataType: uint8, Complexity: real, Dimensions: [75 1]

Data Types: uint8 | UDP_Packet

Length — Number of bytes received

double

This port is available when you disable the Enable Simulink messages parameter. The Length is the number of bytes in the new packet received, otherwise 0. If more bytes are received than can be output through the Data port with width defined by Receive width, the excess bytes are discarded.

Parameters

General Parameters

Use host-target connection — Use Ethernet connection between development and target computers

'off' (default) | 'on'

Dependency

When you select this parameter, it deactivates the Local IP address parameter and excludes the ports 1 through 1023 and 5500 through 5560 from use by UDP.

Programmatic Use

Block Parameter: useHostTargetConn

Local IP address — Destination IP address for receiving data

Use host-target connection (default)

When Local IP address is set to Use host-target connection, the block uses the connection between the development and target computers. Use 0.0.0.0 to bind to INADDR_ANY, which enables the socket to receive broadcast datagrams.

Programmatic Use

Block Parameter: ipAddress

Local port — Destination UDP port to receive data

1–65535

Specifies UDP port to receive data.

Ports 1 through 1023 and 5500 through 5560 are reserved for Simulink Real-Time communications.

Programmatic Use

Block Parameter: localPort

Receive width — Width of Data output vector

1–65504

Determines the width of the Data output vector. If this value is less than the number of bytes in the received packet, the excess bytes are discarded.

Programmatic Use

Block Parameter: rcvWidth

Receive from any source — Causes receiver to accept data from any IP address

on (default) | off

When Receive from any source is on, the block receives data from any accessible IP address. When it is off, the block receives data from only the address that you specify in From IP address.

To make the From IP address parameter visible, clear the Receive from any source check box.

Programmatic Use

Block Parameter: rcvFmAny

From IP address — Source from which to receive data

x.x.x.x

Enter a valid IP address as a dotted decimal character vector, for example, 192.168.7.2. You can also use a MATLAB expression that returns a valid IP address as a character vector.

The address 255.255.255.255 is an invalid IP address.

To make this parameter visible, clear the Receive from any source check box.

Programmatic Use

Block Parameter: fmAddress

Sample time (-1 for inherited) — Sample time of block

-1 (default) | numeric

Enter the base sample time or a multiple of the base sample time.

Programmatic Use

Block Parameter: sampleTime

Enable Simulink messages — Data as messages

off (default) | on

The Enable Simulink messages directs the block to treat data as messages. When enabled, the Length port is removed.

Programmatic Use

Block Parameter: MessageOut

Maximum messages per timestep — Limits messages

1 (default) | int

The Maximum messages per time step value limits the number of messages to permit in a time step. If the number of messages exceeds this limit, an error is generated..

Programmatic Use

Block Parameter: maxPacket

Extended Capabilities

C/C++ Code Generation
Generate C and C++ code using Simulink® Coder™.

Version History

Introduced in R2020b