Community Profile

photo

Torsten Knodt


A123 Systems GmbH

Last seen: alrededor de 1 año hace Con actividad desde 2012

Professional Interests: Rapid Prototyping, Ground Vehicle Physical Simulation, Virtual Integration, Model Based Development, AutoSAR, Symbolic Solutions to Differential Equations, Static and Dynamic Parameter Estimation

Estadísticas

All
  • First Review
  • Thankful Level 1
  • Revival Level 1
  • Knowledgeable Level 1
  • First Answer
  • Scavenger Finisher
  • Commenter
  • Solver

Ver insignias

Content Feed

Ver por

Pregunta


How to continuously repeat the output of the "From Spreadsheet" source block?
Hi, How can I continuously repeat the output of the "From Spreadsheet" source block? The extrapolation at the end does not pro...

más de 4 años hace | 1 respuesta | 0

1

respuesta

Pregunta


How can I draw a mesh into a block mask/ icon?
Hello, I have a masked Simulink block. Now I want to draw a mesh into the icon. Unfortunately the mesh is drawn into an own w...

alrededor de 7 años hace | 1 respuesta | 0

1

respuesta

Resuelto


Compute the step response of a DC motor
Compute the step response of a DC motor shown below <<http://blogs.mathworks.com/images/seth/cody/dc-motor.png>> The param...

más de 7 años hace

Resuelto


Counting pulses in a signal
Count the number of pulses that are the result of summing each pulse generator block. Pulse Generator blocks produce a recurr...

más de 7 años hace

Resuelto


Make a low pass filter
Make a first order low pass filter that will filter out the high frequency oscillations for the given input signal. The cut-off ...

más de 7 años hace

Respondida
Automotive problem - Counting and saving
This depends on your interface to write to the EEPROM. Normally you would count in your RAM and trigger writing to the EEPROM in...

más de 7 años hace | 0

Resuelto


Add offset to a signal
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-offset-eqn.png>> You should see a downward...

más de 7 años hace

Resuelto


Produce a sine wave
Produce a sine wave with amplitude 3: <<http://blogs.mathworks.com/images/seth/cody/sine-eqn.png>>

más de 7 años hace

Resuelto


Produce a cosine wave
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/cosine-eqn.png>>

más de 7 años hace

Resuelto


Connect blocks in a model
Connect the blocks in the model to produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/connect-blocks...

más de 7 años hace

Resuelto


Add a block to a model
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-block-eqn.png>> In this case, the slope of...

más de 7 años hace

Resuelto


Make the vector [1 2 3 4 5 6 7 8 9 10]
In MATLAB, you create a vector by enclosing the elements in square brackets like so: x = [1 2 3 4] Commas are optional, s...

más de 7 años hace

Resuelto


Pizza!
Given a circular pizza with radius _z_ and thickness _a_, return the pizza's volume. [ _z_ is first input argument.] Non-scor...

más de 7 años hace

Respondida
How can i change a value of a resistor during simulation using simpowersystems toolbox ( R L C branch )
I had the same requirement. I either use a voltage measurement together with a controlled current source or a current measureme...

más de 7 años hace | 0

| aceptada

Pregunta


/usr/bin/ld: raccel_sfcn_utils.o: undefined reference to symbol 'dlclose@@GLIBC_2.2.5'
I get the following message when starting a simulation in rapid acceleration mode under Ubuntu Xenial 64 Bit which works under W...

más de 7 años hace | 0 respuestas | 0

0

respuestas

Pregunta


What is the cause of the error message "FIMATH mismatch:Property 'ProductWordLength'" here?
I get the error message FIMATH mismatch:Property 'ProductWordLength': 16 ~= 32 from the following action code in a stat...

más de 7 años hace | 0 respuestas | 0

0

respuestas

Respondida
How to define the sampling time in a system of Simscape Power System Blocks without accuracy lost importants?
Hi Tony, it's hard to give an advice without knowing your model, simulation settings and the intent of your simulation. Becaus...

más de 7 años hace | 0

| aceptada

Pregunta


OutOfMemoryError when building PDF System Design Description for "big" Simulink Model
Hello, I get an OutOfMemoryError when building a System Design Description in PDF and Word format. I already increased the heap...

más de 8 años hace | 0 respuestas | 0

0

respuestas

Pregunta


Initial output value for bus in enabled subsystem hierarchy
I have a hierarchy of subsystems where a middle subsystem is an enabled one. The hierarchical subsystems each have a single outp...

más de 9 años hace | 1 respuesta | 0

1

respuesta

Pregunta


Analyzing and creating fixed-point data types.
Hello, is there a single function to get the minimum and maximum value representable by a specific fixed-point data type? I am ...

alrededor de 11 años hace | 1 respuesta | 0

1

respuesta

Pregunta


Simulink message "Attempt to use invalid data type id 17"
Hello, how can I find out which data type corresponds to a specific id when getting the message "Attempt to use invalid data ty...

más de 11 años hace | 1 respuesta | 2

1

respuesta

Pregunta


"Variable time delay" block in "For Each Subsystem"
Hello, I try to synthesize noise coming from multiple targets to multiple sensors. I have two cascaded for-each sub-systems, th...

alrededor de 12 años hace | 1 respuesta | 0

1

respuesta