Torsten Knodt
A123 Systems GmbH
Followers: 0 Following: 0
Professional Interests: Rapid Prototyping, Ground Vehicle Physical Simulation, Virtual Integration, Model Based Development, AutoSAR, Symbolic Solutions to Differential Equations, Static and Dynamic Parameter Estimation
Estadísticas
9 Preguntas
3 Respuestas
0 Problemas
10 Soluciones
CLASIFICACIÓN
4.232
of 290.008
REPUTACIÓN
12
CONTRIBUCIONES
9 Preguntas
3 Respuestas
ACEPTACIÓN DE RESPUESTAS
44.44%
VOTOS RECIBIDOS
2
CLASIFICACIÓN
of 19.620
REPUTACIÓN
N/A
EVALUACIÓN MEDIA
0.00
CONTRIBUCIONES
0 Archivos
DESCARGAS
0
ALL TIME DESCARGAS
0
CLASIFICACIÓN
31.052
of 144.389
CONTRIBUCIONES
0 Problemas
10 Soluciones
PUNTUACIÓN
120
NÚMERO DE INSIGNIAS
2
CONTRIBUCIONES
0 Publicaciones
CONTRIBUCIONES
0 Público Canales
EVALUACIÓN MEDIA
CONTRIBUCIONES
0 Temas destacados
MEDIA DE ME GUSTA
Feeds
Pregunta
How to continuously repeat the output of the "From Spreadsheet" source block?
Hi, How can I continuously repeat the output of the "From Spreadsheet" source block? The extrapolation at the end does not pro...
más de 4 años hace | 1 respuesta | 0
1
respuestaPregunta
How can I draw a mesh into a block mask/ icon?
Hello, I have a masked Simulink block. Now I want to draw a mesh into the icon. Unfortunately the mesh is drawn into an own w...
alrededor de 7 años hace | 1 respuesta | 0
1
respuestaAutomotive problem - Counting and saving
This depends on your interface to write to the EEPROM. Normally you would count in your RAM and trigger writing to the EEPROM in...
más de 7 años hace | 0
How can i change a value of a resistor during simulation using simpowersystems toolbox ( R L C branch )
I had the same requirement. I either use a voltage measurement together with a controlled current source or a current measureme...
más de 7 años hace | 0
| aceptada
Pregunta
/usr/bin/ld: raccel_sfcn_utils.o: undefined reference to symbol 'dlclose@@GLIBC_2.2.5'
I get the following message when starting a simulation in rapid acceleration mode under Ubuntu Xenial 64 Bit which works under W...
más de 7 años hace | 0 respuestas | 0
0
respuestasPregunta
What is the cause of the error message "FIMATH mismatch:Property 'ProductWordLength'" here?
I get the error message FIMATH mismatch:Property 'ProductWordLength': 16 ~= 32 from the following action code in a stat...
más de 7 años hace | 0 respuestas | 0
0
respuestasHow to define the sampling time in a system of Simscape Power System Blocks without accuracy lost importants?
Hi Tony, it's hard to give an advice without knowing your model, simulation settings and the intent of your simulation. Becaus...
casi 8 años hace | 0
| aceptada
Pregunta
OutOfMemoryError when building PDF System Design Description for "big" Simulink Model
Hello, I get an OutOfMemoryError when building a System Design Description in PDF and Word format. I already increased the heap...
más de 8 años hace | 0 respuestas | 0
0
respuestasPregunta
Initial output value for bus in enabled subsystem hierarchy
I have a hierarchy of subsystems where a middle subsystem is an enabled one. The hierarchical subsystems each have a single outp...
más de 9 años hace | 1 respuesta | 0
1
respuestaPregunta
Analyzing and creating fixed-point data types.
Hello, is there a single function to get the minimum and maximum value representable by a specific fixed-point data type? I am ...
alrededor de 11 años hace | 1 respuesta | 0
1
respuestaPregunta
Simulink message "Attempt to use invalid data type id 17"
Hello, how can I find out which data type corresponds to a specific id when getting the message "Attempt to use invalid data ty...
más de 11 años hace | 1 respuesta | 2
1
respuestaPregunta
"Variable time delay" block in "For Each Subsystem"
Hello, I try to synthesize noise coming from multiple targets to multiple sensors. I have two cascaded for-each sub-systems, th...
alrededor de 12 años hace | 1 respuesta | 0